WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2023. SECTION 8 2023 NEW PRODUCTS 528 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 7 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PART # DESCRIPTION FOR 17-22 M-EIGHT 0928-00911 Stock replacement length and designed to work with factory base circle camshaft dimensions (works with all stock, Screamin’ Eagle and Feuling camshafts) 0928-01131 .040” shorter than stock and designed to work with decked cylinder heads and running thinner head gaskets (works with all Feuling® stock and SE® M-Eight camshafts) 0928-01141 .040” longer than stock and designed to work with factory base circle camshaft dimensions (works with all Feuling®stock and SE® M-Eight camshafts) PART # DESCRIPTION FOR 99-17 TWIN CAM 0928-0101 Stock replacement length and designed to work with factory base circle camshaft dimensions (works with Feuling 525, 543 and 574 cam grinds) 0928-0102 .030” longer than stock and designed to work with smaller base circle camshafts (works with Feuling 594 and 630 cam grinds) 1 Due to the unstable nature of this 4-valve engine design with one rocker arm activating two valve springs, Feuling® highly recommends running one-piece pushrods instead of quick-install adjustable pushrods to maintain maximum cam/valve lift and reduce valve train harmonics and associated hydraulic lifter issues. HP+® ONE-PIECE PUSHRODS • Feuling highly recommends using one-piece pushrods instead of adjustable pushrods to maintain maximum cam/valve lift and reduce valvetrain harmonics and associated hydraulic lifter issues • Fixed length, 4130 chromoly one-piece pushrods with swedged formed ends • Heavy-duty 7/16” diameter tube with a wall thickness of .165” • Heat-treated with a black oxide finish • Made in the U.S.A. NOTE: Requires removal of rocker covers and rocker arms for installation. PART # DESCRIPTION FOR 99-17 TWIN CAM 0928-0009 HP+® .120” wall thickness PART # DESCRIPTION FOR 99-17 TWIN CAM (CONT) 0928-0010 Race Series® .145” wall thickness HP+® AND RACE SERIES® ADJUSTABLE PUSHRODS • Maintain maximum valve lift • Increased stiffness and column rigidity maximizing valve-train stability, increasing engine rpm horsepower and torque output • Adjustable pushrods are 3/8”, 4130 chrome moly tube and use a minimal adjustment parameter eliminating flex and loss of valve train stability problems associated with most adjustable pushrods • Individual length intake and exhaust pushrods keep the adjustment extension to a minimum • Designed to exceed the needs of performance engines using larger lift camshafts and high spring pressures, while maintaining proper and critical oil flow to top end valve gear • For use with hydraulic or solid lifters and street or race engines • HP+ and Race Series pushrods require removal of rocker covers and rocker arm supports, Feuling Quick install rods (PART #0928-0105) can be installed without removing the rocker covers, arms and supports • Feuling HP+ and Race Series pushrods can be used with the factory pushrod tubes • PART #0928-0009 HP+ pushrods have 24 threads per inch adjustment, super strength single jam nut lock system, wall thickness 0.120” • PART #0928-0010 Race Series pushrods have 24 threads per inch with 0.145” wall thickness (recommended when extreme valve-spring pressures are used) • Made in the U.S.A. NOTE: HP+ and Race Series adjustable pushrods can be adjusted 0.225” over stock length to accommodate longer cylinders and smaller base circle camshafts. NOTE: To ease installation on Twin Cam applications use Pushrod Tube Kit PART #s 0928-0016 or DS-193758; not required. NOTE: Requires removal of rocker covers and rocker arm supports for installation. PART # DESCRIPTION 0927-0030 For S&S standard and roller rocker arms ROCKER ARM BUSHING • Replacement bushing for S&S roller rocker arms • Sold each • Made in the U.S.A. PART # DESCRIPTION 146819 For 99-17 Twin Cam, 86-20 XL and 94-09 Buell (except 1125R) ROCKER ARM BUSHINGS • Manufactured from solid billet bearing bronze bar stock • .555” ID • Sold in packs of eight • Made in the U.S.A. PART # DESCRIPTION DS-193821 For 99-17 Twin Cam, 86-21 XL (except 21 Sportster S/RH 1250S); repl. OEM #17428-57 ROCKER ARM BUSHINGS • Manufactured from solid billet bearing bronze bar stock • ID 0.547” • Sold in packs of eight • Ream to fit 0928-0091 0928-0102 0928-0009
RkJQdWJsaXNoZXIy NDI5NTY=