WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2023. SECTION 8 2023 NEW PRODUCTS 566 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 7 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PART # DESCRIPTION 2401-09931 For 17-22 M-Eight engines w/ Feuling high flow camplate and HP+ or Race Series oil pumps (do not use washers with ARP® oil pump bolts) 2401-0127 For 99-17 Twin Cam engines w/ Feuling HP+, Race Series or OE+ camplates and oil pumps 1 Not for use with OE+ camplates/oil pumps. CAMPLATE/OIL PUMP FASTENER KITS • Optional kit for Feuling camplates/oil pumps only • Quality 12-point, heat-treated 8740 chromoly steel bolts with black oxide finish manufactured by ARP® to Feuling’s exact specifications • Precision-rolled threads provide optimum engagement, prevent galling and promote consistent torque loading • Wide, underhead flange design provides even load distribution for optimum sealing of surfaces to prevent leaks • Tensile strength rated at 170,000 psi; superior and stronger than OEM and stronger than grade 8 fasteners • Includes moly assembly lubricant for installation • Made in the U.S.A. PART # DESCRIPTION FOR 07-17 TWIN CAM AND 06 DYNA 0925-01101, 2 For chain or gear drive cams FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0920-00063 For gear drive cams PART # DESCRIPTION FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) (CONT) 0925-04404 Hydraulic tensioner conversion camplate for stock chain drive cams HIGH FLOW CAMPLATES FOR TWIN CAM • Increase engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages • Camplate matches the oil port holes throughout the camplate to the port holes in the engine case increasing engine oil flow throughout the engine • 25-35 degree cooler engine temperatures and 20-30 degree cooler oil temperatures • Made from 7075 billet aluminum which is 50% harder and stronger than the factory, SE® and other aftermarket camplates • The 7075 increases the strength and hardness of the camplate, holding tighter tolerances under temperature eliminating flexing and the need for bronze bushings • Camplates are pressure tested and pressure relief valve is seated, sealed and set to pop off at 55-60 psi • When matched with the Feuling® Race Series oil pump rear wheel power gains of 3 Horsepower and 4 ft/lbs of Torque can be achieved • For use ONLY with the Feuling® oil pumps • Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerances for improved press fit 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 Requires the use of 07-17 style Feuling HP+ or Race Series oil pump PART #s 0932-0023 or 0932-0026. 3 Requires the use of 99-06 style Feuling HP+ or Race Series oil pump PART #s 0932-0018 or 0932-0020. 4 Requires 07-17 hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kit PART #s 0925-1069 or 0925-1070. • Bearing and retainer plate hardware is included • Camplates for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal tolerance for improved cam fitment • Added cam journal oil groove for cold startup protection and increased cam journal lubrication • Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear • Made in the U.S.A. 2401-0127 2401-0993 0925-0110 0925-0440 PART # DESCRIPTION 0932-0036 For 17-22 M-Eight, 07-17 Twin Cam and 06 Dyna camplates BLOCK-OFF PLATES • Block-off hydraulic chain tensioner holes when using gear-driven cams • Made in the U.S.A. PART # DESCRIPTION 0925-0914 For 07-17 Twin Cam and 06 Dyna models 0925-09151 For 99-06 Twin Cam models (except 06 Dyna) w/ Gear Drive Cams 1 Accepts 07-16 style oil pumps only. CAMPLATE FOR TWIN CAM • Precision CNC-machined forged aluminum • Adjustable oil pressure regulator; adjust without removing plate from the engine • Passage plugs are removable for service • Rebuildable bronze pinion shaft bushing in all models and bronze cam bushings in 07-later style • Made in the U.S.A. NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. 0925-0914
RkJQdWJsaXNoZXIy NDI5NTY=