WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 8 All part numbers in BLUE are new for 2023. 2023 NEW PRODUCTS 573 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 7 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PART # DESCRIPTION 0932-01061 For 07-17 Twin Cam and 06 Dyna models PART # DESCRIPTION 0932-0107 For 99-06 Twin Cam models (except 06 Dyna and 00-02 Softail models) 1 Will not fit 00-02 Softails when used with a TC3 cam plate. TC3 OIL PUMPS FOR TWIN CAM • Three stages for consistent pressure and reliable scavenging • Separate scavenge sections for flywheel cavity and cam chest (no interface) • Screens and magnetic traps help protect the scavenge rotors from debris • Special design allows S&S pumps to tolerate more pinion shaft run-out without damage • Made in the U.S.A. NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. PART # DESCRIPTION 0932-0088 For 07-17 Twin Cam and 06 Dyna models 0932-0087 For all 99-06 Twin Cam (except 06 Dyna models) HIGH-PERFORMANCE TWIN CAM OIL PUMPS • Helps to reduce oil carryover during high rpm operation; higher volume helps reduce engine and oil temperatures • 53mm diameter rotors for maximum performance • Gain of 20% oil pressure, 125% pressure volume and 135% scavenge volume over OEM stock TC88 oil pumps • Gain of 16% oil pressure, 66% pressure volume and 100% scavenge volume over OEM stock TC96/103 oil pumps • High-quality die-cast aluminum body construction, high-strength steel gear construction • Fits both stock and aftermarket cam support plates for seamless installation NOTE: Does not fit Screamin’ Eagle cam plate. PART # DESCRIPTION 0932-0236 For 17-22 M-Eight air-cooled motors HIGH-PERFORMANCE M-EIGHT OIL PUMP • 126% feed and 131% scavenge volume compared to OEM (stock) M8 fourth generation oil pumps at 1000 rpm • 123% feed and 146% scavenge volume compared to OEM (stock) M8 fourth generation oil pumps at 2500 rpm • Scavenge side discharge was improved by modifying the suction ratio to help eliminate sumping from excess oil in the crankcase • Improved oil flow by inserting an oil passage correction spacer between the large-capacity oil pump body and the cam support plate PART # DESCRIPTION 0932-0189 For 91-22 XL (Except 21-22 Sportster S/RH1250S, 22 Nightster/RH975) OIL PUMP ASSEMBLY • High-quality replacement cast aluminum pump body with steel gears and shaft • Raw cast-aluminum finish • Gaskets and seals included PART # DESCRIPTION 0932-0019 For Feuling® oil pump PART #s 0932-0018 and 0932-0020 0932-0024 For Feuling® oil pump PART #s 0932-0023 and 0932-0026 OIL PUMP REBUILD KITS • Include everything needed to rebuild Feuling® HP+® and Race Series oil pumps • Kit comes with new O-rings, separator plate and installation instructions • Made in the U.S.A. 0932-0019 0932-0088 0932-0106
RkJQdWJsaXNoZXIy NDI5NTY=