WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2023. SECTION 11 2023 NEW PRODUCTS 698 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 7 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PART # DESCRIPTION 2101-0033 For carbureted 99-03 Twin Cam models PART # DESCRIPTION 2101-0022 Optional programming kit DYNA 2000TC PROGRAMMABLE DIGITAL PERFORMANCE IGNITION MODULE • Single-fire, fully programmable performance ignition • Sixteen programmable advance curves in three groups: stock-to-slightly-modified motors, heavily-modified motors and insanely-modified motors • Eight rev limiter settings in 250 rpm steps from 5750-7250 rpm • All functions offer full digital accuracy • Compatible with stock and performance coils – less than 1-ohm resistance • Coil current constantly monitored to provide constant full-spark energy • Uses all stock sensors and connectors • Built-in reverse battery and spike protection PART # DESCRIPTION 2101-0063 For carbureted 04-06 Twin Cam models PART # DESCRIPTION 2101-0071 For 04-06 XL DYNA 2000TC-3 DIGITAL PERFORMANCE IGNITION MODULES • Module has a single connector • Loaded with 16 different advance curves, giving engine builder a wide range of curves to work with • Adjustable rev limiter allows the user to select a rev limit ranging from 5750 to 7500 rpm in 250 rpm steps • Made in the U.S.A. PART # DESCRIPTION PLUG-IN IGNITION MODULES 2101-0034 For 04-06 Twin Cam and Sportster carbureted models w/ a single 12-pin connector DS242377 For 99-03 Twin Cam carbureted models w/ two 12-pin connectors 2101-02191 For 99-03 Twin Cam carbureted models w/ two 12-pin connectors and two-stage rev limiter (race only) OPTIONAL ACCESSORIES 2101-0075 USB interface 1 Requires USB interface (PART #2101-0075) to program. PLUG-IN IGNITION MODULES • Features two advance curve families that are adjustable to accommodate stock and modified engines • Selectable multi-spark mode for quick starting and smooth cruising • Four rotary switches for mode select, timing adjustments, advance slope and rpm limit (in 100 rpm steps) • Coil outputs protected against short circuits • Requires OEM coils with less than 1 ohm primary resistance and low-resistance spiral-core or carbon-core suppression-type plug wires • 12V power adapters are used to power up the modules when removed from the bike (sold separately) • Optional USB interface (PART #2101-0075) and software required for programming custom curves (programs available on website www.daytona-twintec.com/index.html) • Includes easy-to-follow instructions • Made in the U.S.A. NOTE: Will not work on fuel-injected models. NOTE: Exempt per CARB Executive Order (E.O.) #D-641-1. • Data recording includes total engine hours, time wide-open throttle, longest time operating at wide-open throttle, max rpm, seconds near rev limit and number of engine starts • PC programmability makes possible an eight-point, fully definable, wide-open throttle curve and a fully definable part-throttle curve, programmable rev limit in 50 rpm steps, 0-5 programmable dead-cranking revs, total of +/- 10° rear cylinder offset, programmable rev limiter, and security lock-out (pin # activated) • Made in the U.S.A. 2101-0033 2101-0022 2101-0063 2101-0071 2101-0034 2101-0219 2101-0075
RkJQdWJsaXNoZXIy NDI5NTY=