WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 1 All part numbers in BLUE are new for 2023. 2023 NEW PRODUCTS NP73 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 7 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. RACE SERIES® OIL SYSTEM PACKS FOR M-EIGHT • Includes Fueling's® High Flow billet camplate made from 7075 aluminum which is 50% harder and stronger than the factory or Feuling OE+ camplates • Increases oil flow and volume by enlarging the oil pump reservoirs and critical oil passages including matching the oil portholes throughout the camplate to the portholes in the engine case which increases engine oil flow to the lifters, piston cooling jets, crankshaft and rod bearings • Feuling oil pumps are bench tested, the relief valve is seated and sealed to a minimum of 30 psi with full pop off at 55-60 psi • Increased oil volume from the larger gears and properly sized passages along with the pressure relief valve seat and seal from these oil pumps is essential for proper oiling system function • Fueling® oil pump and camplate combination eliminate common pressure and scavenge issues associated with the factory oiling systems • Quieter and smoother engine operation • Increase oil pressure, scavenge volume and engine oil flow • 42% more scavenge volume with port sizing, matched passages and holes to the engine case • 68% more oil volume to the crankshaft and connecting rod bearing • 15-25 degree cooler engine temperatures • 15-30 degree cooler oil temperatures • 10-30 more psi of oil pressure • M-Eight Twin-Cooled™ motor oil pump specs: 30% more pressure gear volume over stock and 53% more scavenge gear volume over stock • M-Eight Oil-Cooled motor pump specs: 27% more pressure and scavenge gear volume over stock • Reduces wet sumping, blowby and oily air cleaners PART # DESCRIPTION 0932-0293 For 17-22 M-Eight oil-cooled motors w/ gear or chain drive 0932-0294 For 17-22 M-Eight Twin-Cooled™ motors w/ gear or chain drive • Test results show 2 HP gain and 2 ft/lbs of torque gain to the rear wheel on M-Eight • Includes a Race Series® oil pump, Race Series® short-travel hydraulic roller lifters, High Flow camplate and cam installation kit, cam bearing, cam/crank bolts and washers, engine and fastener assembly lube • Billet 7075 aluminum oil pump which is 50% harder and stronger than the factory pump holding tighter tolerances under temperature • Race Series® oil pumps feature increased scavenge side kidney port volume over HP+ oil pumps • Race Series® short-travel hydraulic lifters have .115" of total travel and will increase rpm by decreasing valve float and valve-train harmonics while maintaining a quiet engine • The travel reduction reduces the amount of oil that is required to fill the inside of the lifter which reduces oil aeration inside the lifter on steep, fast action high lift camshaft lobes • Made in the U.S.A. • See page 569 of the 2023 Parts Canada FatBook for the entire line of Feuling HP+ Oil System Packs NOTE: Optional Fueling X ARP bolt kit available for the High Flow camplate PART #0932-0192 and HP+ or RS oil pump combo. See PART #2401-0993, optional ARP oil pump bolts do not use washers. NOTE: Feuling test results show as much as 50% reduction of engine sump oil level. NOTE: M-Eight engines must check clearance on front exhaust lifter to camshaft flange fit. NOTE: Block-off plate PART #0932-0036 required when using gear drive cams. NOTE: Use with short-travel pushrods PART #0928-0114 on stock base circle camshafts with Feuling short-travel lifters (includes Feuling grinds 405, 465, 472, 508, 521 and 592). 0932-0293
RkJQdWJsaXNoZXIy NDI5NTY=