WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS &MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for the OldBook. SECTION 7 298 See FATBOOK For Late Model Applications DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. GRIND OPEN CLOSE DURATION @ .053 VALVE LIFT EV3 Intake 21° 37° 238° .495” Exhaust 43° 15° 238° .495” EV13 Intake 15° 31° 226° .485” Exhaust 45° 13° 238° .495” EV23 Intake 10° 30° 220° .498” Exhaust 40° 8° 228° .498” EV27 Intake 20° 36° 236° .495” Exhaust 44° 16° 240° .495” GRIND OPEN CLOSE DURATION @ .053 VALVE LIFT EV46 Intake 25° 41° 246° .495” Exhaust 49° 17° 246° .495” EV51 Intake 28° 44° 252° .510” Exhaust 54° 22° 256° .510” EV72 Intake 30° 54° 264° .560” Exhaust 60° 28° 268° .560” J Intake 21” 41” 242° .405” Exhaust 41” 21” 242° .405” ANDREWS CAMS BIG TWIN Andrews Products grinds its cams with the help of a computer with cam design capabilities. This superior technology gives the utmost in both performance and reliability. Only the best alloy steel billets and heat-treating processes are utilized. Furthermore, the power in Harley’s Evolution engines can be made even more convincing when a superior Andrews computer-designed high-performance cam is installed. These hydraulic lifter cams are capable of 6000-plus rpm with stock springs and no valve float. Made in the U.S.A. PART # DESCRIPTION EV13 CAM DS-199323 For 84-99 Evolution Big Twin PART # DESCRIPTION EV23 CAMS DS-199097 For 84-99 Evolution Big Twin 110715 For 84-99 Evolution Big Twin (without gear) PART # DESCRIPTION EV27 CAMS DS-199344 For 84-99 Evolution Big Twin 110716 For 84-99 Evolution Big Twin (without gear) PART # DESCRIPTION EV3 CAM DS-199320 For 84-99 Evolution Big Twin PART # DESCRIPTION EV46 CAMS 110720 For 84-99 Evolution Big Twin (without gear) EV3 GRIND CAM • Bolt-in cam for light bikes (FXRS, etc.) adds significant mid-range power without affecting idle • A 6000+ rpm cam for stock heads and springs with hydraulic lifters EV13 GRIND CAM • Bolt-in cam for street or touring use with more mid-range and upper-end power than the stock 88 EV cams • Especially effective in reducing oil temperature • Uses stock springs; works with carbs or fuel injection EV23 GRIND CAMS • Bolt-in cam for heavier touring bikes and high-geared bikes with 65-tooth rear pulleys • Crisp throttle response and strong pulling power from 1500 to 6000 rpm • Works well in higher altitudes • Uses stock springs; works with carbs or fuel injection EV27 GRIND CAMS • Bolt-in street cam with fast open and close ramps • Similar timing to EV3, but designed to produce a very broad torque band • Pulls from 1500 to 6000 rpm • Uses stock springs; works with carbs or fuel injection EV46 GRIND CAM • Bolt-in performance cam with fast open and close ramps • Similar to “EV3” but higher static compression pressure for 4000+ rpm with stock heads and hydraulic lifters PART # DESCRIPTION EV51 CAM DS-199447 For 84-99 Evolution Big Twin EV51 GRIND CAM • Long duration for modified street motors • Works with stock hydraulics • Easy installation • Power range from 3000-6500 rpm NOTE: Must check coil bind, valve-to-valve clearance and valve-to-piston clearance. NOTE: On late 77 and later engines, the pitch diameter on the camshaft, pinion gear and the breather valve gear was changed. These components are not interchangeable with earlier-style components unless replaced in sets only. Late 77 and later gear sets are identified by a circular groove machined in the outer face of the cam gear. PART # DESCRIPTION EV72 CAM DS-199194 For 84-99 Evolution Big Twin EV72 GRIND CAM • Upgraded EV7, for 92” or larger street motors • For use with Andrews springs and titanium collars • Very broad powerband, 2800-6000 rpm • OK for use with hydraulic lifters PART # DESCRIPTION J CAMS DS-199301 For 48-69 Big Twin “J” GRIND CAMS • For mild street applications • Add more power throughout rpm range and maintain a smooth idle • Bolt-in with no head work
RkJQdWJsaXNoZXIy NDI5NTY=