WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS &MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for the OldBook. SECTION 10 398 See FATBOOK For Late Model Applications DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PART # DESCRIPTION 2102-0021 3-ohm single-fire coil w/ electronic ignition 3 OHM HIGH-OUTPUT SINGLE-FIRE IGNITION COIL • This single-fire coil is actually two separate coils in a single package • Works well with any single-fire ignition system • Made in the U.S.A. PART # DESCRIPTION FOR 70-84 SHOVELHEAD, 70-85 XL 2101-0345 HI-4N ignition module only 2101-0346 HI-4N ignition module, ignition coil and plug wires HI-4N IGNITION MODULE KIT • More power than the stock ignition • Single-fire and dual-fire function built into a single module • All-metal housing provides improved heat dissipation • Ignition advance and timing degree markings are on the metal flange • Convenient cable notch in the housing makes installation easier and prevents damage to the cable • Sensor and magnet housings are built into the all-metal back plate to protect the sensors from damage during installation • Sensor housings contain advanced flux concentrators with high-temperature-resistant samarium/cobalt magnets for accurate, reliable ignition triggering • Electronics are fully enclosed to resist vibration, moisture and dirt • All electronics are mounted directly to the metal housing, which acts as a heat sink • Four rotary switches for ignition mode selection, advance rate and rev limit • Switches provide accurate, repeatable settings • PART #2101-0346 includes ignition module, S&S ignition coil and correct-length spark plug wires; PART #2101-0345 includes HI-4N ignition module only • Made in the U.S.A. NOTE: Not for fuel-injected models. PART # DESCRIPTION DC6-5 Twin Fire II Miniature, dual output towers TWIN FIRE II COIL • Single-fire just got easier • High-technology materials now make it possible to put two coils in the same space as the stock coil with greater output • No exposed laminations to rust and degrade performance • High voltage and primary terminals machined from brass • High-impact thermoplastic housing is ultrasonically welded and sealed against moisture • Compact size fits easily under stock covers • Peak gap current in excess of 50mA • Over 40,000V per output • Rated at 3 ohms; accepts 7mm to 8mm wires • Made in the U.S.A. NOTE: Not for use with DS6-2 ignition system. PART # DESCRIPTION DC6-4 Twin Fire, four output towers TWIN FIRE COIL • Design incorporates two individual performance ignition coils into a single, easy-to-mount package that is only slightly larger than the stock coil and uses the stock mounting bracket • Delivers spark voltage in excess of 30,000V with fast rise times and high energy • For all single-fire, dual-plug head applications • Can be used with any electronic advance ignition system that incorporates dwell control, but cannot be used with the DS6-2 Dyna S or similar ignitions • All coils are rated at 3 ohms • Made in the U.S.A. NOTE: Not for Twin Cam applications. PART # DESCRIPTION 2102-0001 3-ohm, dual tower coil, single-fire, dual-plug (pr.) 2102-0002 3-ohm, single tower coil, single-fire, single-plug (pr.) MINIATURE SERIES COILS • One of the smallest packages delivers high output with advanced magnetic core technology • Designed for use with Dyna 2000 and 3000 series ignitions, factory-installed electronics, or with aftermarket ignitions that employ dwell control • Secondary resistance is 11.5-ohms • Great for customs where coils need to be hidden NOTE: Not for use with the Dyna “S,” DYNA III or earlier generation ignitions. PART # DESCRIPTION DC10-1 5 ohm (black), angled single output street application (pr.) DC3-1 3 ohm (green), angled single output, for use with DS-62 single-fire ignition only race application (pr.) DC2-1 1.5 ohm (brown), angled dual output (pr.) DC1-1 3 ohm (green), angled dual output (pr.) PART # DESCRIPTION DC6-1 3 ohm (green), straight dual output, Std. H-D style (85-up electronic ignition) (ea.) DC8-1 5.0 ohm (black), angled dual output (points) (pr.) DC7-1 5.0 ohm (black), straight dual output with single-plug heads 12V COILS • The “industry standard” with 35,000V spark energies second to none • Designed to work with any Dyna ignition system • Can be used for single- or dual-plug applications • Made in the U.S.A. 2101-0345 2102-0001 2102-0002 DC3-1 DC10-1 DC2-1 DC1-1 DC7-1 DC8-1 DC6-1
RkJQdWJsaXNoZXIy NDI5NTY=