BOLD MAGENTA part numbers are new for 2023 FUEL/AIR SYSTEMS PARTSCANADA.COM STREET | 2023 1025 DISCLAIMER: SEE PAGE 6 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PREMIUM FUEL LINE • Stronger and more durable than vinyl fuel line • Use with any type of gasoline • Resists swelling and hardening • Resistant to direct sunlight, hardening and/or cracking • Flexible in temperatures from -35° F to +165° F • Fuel line stretches easily over fittings or petcocks • Sold in 3’ lengths and 25’ rolls NOTE: Not for use with fuel-injected models. DESCRIPTION PART # 1/8” ID – 3’ LENGTH Clear 0706-0138 3/16” ID X 5/16”OD – 3’ LENGTHS Gray 0706-0038 Clear 0706-0041 Black 0706-0044 1/4” ID X 7/16”OD – 3’ LENGTHS Gray 0706-0039 Clear 0706-0042 Black 0706-0045 DESCRIPTION PART # 5/16” ID X 1/2”OD – 3’ LENGTHS Gray 0706-0040 Clear 0706-0043 Black 0706-0046 1/8” ID – 25’ ROLL Clear 0706-0139 3/16” ID X 5/16”OD – 25’ ROLLS Gray MP12-031 Clear 0706-0021 Black 0706-0018 DESCRIPTION PART # 1/4” ID X 7/16”OD – 25’ ROLLS Gray MP12-032 Clear 0706-0022 Black 0706-0019 5/16” ID X 1/2”OD – 25’ ROLLS Gray MP12-033 Clear 0706-0023 Black 0706-0020 BRAIDED FUEL LINES • Nylon-reinforced vinyl fuel line • Braided nylon within the tubing wall provides added strength • Outstanding appearance for custom fuel lines • Flexible down to 25°F • Maximum operating temp is 150°F • Sold in 3’ lengths and 25’ rolls NOTE: Not for use with fuel-injected engines. DESCRIPTION PART # 3/16” ID 3’ Length 877261 25’ Roll 877212 1/4” ID 3’ Length 877262 25’ Roll 877213 DESCRIPTION PART # 5/16” ID 3’ Length 877263 25’ Roll 877214 3/8” ID 3’ Length 877264 25’ Roll 877215 PVC VENT LINES • Constructed of soft, flexible plasticized PVC tubing • Safe to use with any type of gasoline or alcohol-type fuel • Smooth hard bore helps prevent interior buildup • Recommended for venting and overflow lines • Flexible down to 0°F • Maximum dry heat temp is 220°F • Sold in 3’ lengths and 25’ rolls NOTE: Not for use with fuel injected engines. DESCRIPTION PART # 1/8” ID 3’ Length 877265 25’ Roll 877207 3/16” ID 3’ Length 877266 25’ Roll 877208 1/4” ID 3’ Length 877267 DESCRIPTION PART # 1/4” ID (CONT) 25’ Roll 877209 5/16” ID 25’ Roll 877210 3/8” ID 3’ Length 877269 25’ Roll 877211 LP (LOW PERMEATION) PREMIUM FUEL LINE • Certified to meet permeation emission standards of 15g/M2/day • On emission-controlled vehicles, check with local and state agencies to determine suitability • Robust multi-layer design and construction • Fluoropolymer liner compatible with higher ethanol-blend gasoline up to 100% • Highly flexible, easy to install and offers excellent fitting retention • Resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids • Ozone and UV light resistant • Wide temperature range from -20˚F to 165˚F (-28.9˚C to 73.9°C) DESCRIPTION PART # 1/4” ID 3’ L 0706-0204 DESCRIPTION PART # 1/4” ID (CONT) 25’ L 0706-0206 DESCRIPTION PART # 5/16” ID 3’ L 0706-0205 DESCRIPTION PART # 5/16” ID (CONT) 25’ L 0706-0207 Gray Clear Black • Yellow color for easy identification • Use Stepless® Clamps WARNING: Not for use with fuel injected engines NOTE: #SNG-ENAPNR-OA-03. NOTE: Exempt per EPA CARB E.O. #Q-09-028 for off-road use.
RkJQdWJsaXNoZXIy NDI5NTY=