BOLD MAGENTA part numbers are new for 2023 V-TWIN TOOLS PARTSCANADA.COM TIRE & SERVICE | 2023 429 PART # DESCRIPTION 3801-0084 For 03-10 Twin Cam engines PART # DESCRIPTION 3801-0108 Repl. sleeve kit TIMKEN® CASE BEARING TOOL • For building big-cubic-inch, late-model Twin Cam engines • Can also be used to replace bearings for stock 88” or 96” engines utilizing the JIMS precision insert • Easily and accurately converts the left-side crankshaft roller bearing (OEM #24604-00D) to the more durable Timken® bearing (OEM #9028) • Sleeve is several times stronger than stock aluminum case material that standard bearings ride in • Included in kit is one new steel bearing insert sleeve (held to under .0002” total indicator reading), all necessary drill bits to drill oil feed and return holes, press plate that holds bearing sleeve insert in line with case bearing bore at time of installation, all necessary hardware and instructions • Requires normal hand tools, hand drill and two-ton press • Timken® bearing not included; see PART #0924-0108 • Replacement Timken® sleeve kit available separately • Made in the U.S.A. PART # DESCRIPTION 3801-0062 For 06 Dyna models and all 07-17 Twin Cam models CASE SPLITTER TOOL • ”Breaks” the case sealant by pushing apart both case halves • Bolts to primary mounting holes • Uses included hand thread-in pushing screw • Flywheels will be pushed from the left case • Made in the U.S.A. PART # DESCRIPTION DS-196089 For 55-06 Big Twin, except 06 Dyna CRANK ASSEMBLY REMOVING TOOL • Use to press flywheels from cases • Will press cases apart and break sealant bond • Made in the U.S.A. NOTE: On Twin Cam B motor, will only remove flywheel from left case. PART # DESCRIPTION 3801-0345 For 17-20 M-Eight 107”, 114” 3801-0130 For 99-17 Twin Cam 88”, 96” or 103”, 3.75”-3.875” 3801-0129 For 99-17 Twin Cam Screamin’ Eagle, 4”-4.060” PART # DESCRIPTION DS-196212 For 66-99 Big Twin cylinders, 3.4375”-4” bore w/ stock bolt pattern DS-196213 Adapter bolt kit for 86-03 XL, 94-03 Buell (for use w/ PART #DS-196212) CYLINDER TORQUE PLATES • Torque plates must be used when boring or honing late-model aluminum cylinders • Simulate running stress conditions • Instructions included • Made in the U.S.A. PART # DESCRIPTION 3801-0251 Tappet adjustment tool TAPPET GO-NO-GO TOOL • Simplifies the way to verify proper tappet adjustment • If the tip doesn’t fit between the clip and the pushrod seat or if there is up and down end play, the tappet is out of adjustment • For use on most hydraulic tappets, OEM and aftermarket, for Twin Cam or Evo • Will not work on Solids, JIMS Hydrosolids or other limited travel tappets • Made in the U.S.A. PART # DESCRIPTION 3801-0192 Tappet pump and test stand for 99-20 Big Twin hydraulic tappets 3801-01931 Adapter for 84-99 Evo hydraulic tappets 1 Must be used in conjunction with PART #3801-0192. TAPPET PUMP AND TEST STAND • Use to fill hydraulic tappets before assembling valve train • Help diagnose loose or spongy tappets that can lead to bleed-down issues or sticky tappets that won’t pump up due to poor hydraulic unit fitment • Made in the U.S.A. 3801-0084 3801-0345 DS-196212 3801-0192 3801-0193
RkJQdWJsaXNoZXIy NDI5NTY=