BOLD MAGENTA part numbers are new for 2023 PARTSCANADA.COM 2023 | TIRE & SERVICE V-TWIN TOOLS 430 PART # DESCRIPTION 3801-0292 For 84-20 Big Twin hydraulic tappet assemblies VACUUM LIFTER “PUMP UP”TOOL • Bleeds and pumps up hydraulic lifters • Special jar, designed for vacuum, holds up to four hydraulic lifters in a convenient tray • Apply the vacuum to fully bleed the lifters and have them ready to install • Removes the risk of using starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bled • Made in the U.S.A. PART # DESCRIPTION 3801-0259 For 99-17 Twin Cams ROCKER BOX ALIGNMENT SCREWS • Prevents misalignment of cover, compromising of seal and potential rocker interference • Sold in pairs • Made in the U.S.A. PART # DESCRIPTION 3801-0261 For L76-17 Big Twin (except M-Eight) TAPPET BLOCK/OIL PUMP ALIGNMENT TOOL • Big Twin tappet blocks do not have counter-bored bolt holes; therefore, when a tappet block is removed (or even just loosened) it should be reinstalled using an alignment tool to ensure that the lifters track properly on the camshaft • This tool makes the process quick and easy, ensuring the durability of your installation • Tool also aligns Twin Cam oil pump to the cam support plate; two tools required • Sold each • Made in the U.S.A. PART # DESCRIPTION DS-197077 For L76-17 Big Twin (except M-Eight) TAPPET BLOCK/OIL PUMP TO CAM PLATE ALIGNMENT TOOL • Used to align oil hole from crankcase to tappet block • Can also be used to align rocker box bases on Evolution head (requires two tools) • Aligns Twin Cam oil pump to cam support plate; two required • Sold each • Made in the U.S.A. PART # DESCRIPTION 3801-0275 For all 99-17 Twin Cam engines and 00-20 XL and Buell (except 1125R) TAPPET POSITION HOLDING TOOL • Safely stores anti-rotation pins and tappets for proper and accurate installation • Locations of the tappets are marked on the tool; prevents damage after being removed from the engine • Made in the U.S.A. PART # DESCRIPTION DS-198638 For 70-99 Big Twin TAPPET OIL SCREEN PLUG TOOL • Used to remove the tappet oil screen plug • Removes oil screen without removing exhaust • Made in the U.S.A. PART # DESCRIPTION 3801-0002 Tappet screen plug tool TAPPET SCREEN PLUG TOOL • For use on 70-99 Big Twin (except Twin Cam) with slotted screw tappet oil filter screen cover • Designed for use with 7/16” combination wrench to allow for maximum rotation without touching engine cases • O-ring design retains the tool in wrench or socket • Flange design allows downward force to be applied to tool • Can be used without removing exhaust pipes on most bikes • Tappets should be serviced every oil change PART # DESCRIPTION DS-197058 For all Big Twin oil pumps (except Twin Cam/M-Eight) OIL PUMP SNAP RING INSTALLER • Allows easy installation of outer snap ring on oil pump shaft without stretching the snap ring • Made in the U.S.A. PART # DESCRIPTION 3801-0318 For 17-20 M-Eight and 99-17 Twin Cam CYLINDER HOLD DOWN NUTS • Help to keep the cylinders in place when removing the heads from the engine • One end fits Twin Cam models and the other fits M-Eight engines • Sold in a set of two • Made in the U.S.A. PART # DESCRIPTION DS-197009 Oil pump jig CRANKCASE OIL PASSAGE DRILLING JIG • Used to install S&S oil pumps on early motor cases • Jig is made from steel and heat-treated for durability • Made in the U.S.A.
RkJQdWJsaXNoZXIy NDI5NTY=