BOLD MAGENTA part numbers are new for 2023 V-TWIN TOOLS PARTSCANADA.COM TIRE & SERVICE | 2023 437 PART # DESCRIPTION 3801-0169 Pushrod cover clip installer/remover PUSHROD COVER CLIP INSTALLATION/REMOVAL TOOL • Will not mar or slip • Installs/removes clip professionally with just one hand in seconds • Constructed of tough black Delrin® • For use on all V-Twins that use pushrod clips • Made in the U.S.A. PART # DESCRIPTION 1601-2397 For Twin Cam, Evolution, Shovelhead, Panhead and XL models PUSHROD TUBE TOOL • Used to install and remove pushrod tube clips PART # DESCRIPTION 3801-0159 Pushrod tube holder tool PUSHROD TUBE HOLDER TOOL • Makes for easy adjustment of adjustable pushrods, holding pushrod tubes up and out of the way • Sold each • Made in the U.S.A. PART # DESCRIPTION 115128 For 05-17 Twin Cam w/ 7mm valves (7mm dia.) 115257 For Panhead/Shovelhead valves SOLID CARBIDE VALVE GUIDE REAMERS • Features 2” long pilot for perfect alignment with the valve guide while reaming • One size allows to fit both intake and exhaust if any AV&V valves and guides are used • Solid carbide PART # DESCRIPTION 3801-0269 Valve guide reamer PRECISION MANGANESE VALVE GUIDE REAMER • Manufactured from tough, high-speed steel specifically for use with manganese bronze valve guide • Cutting edge is ground to within +/- .0002” • Spiral fluted reamer incorporates a 1.00” long piloted lead to assist in keeping the reamer aligned with the valve guide centerline • Cutting length is 2.626”, overall length is 7.125” L • Sold each 115257 PART # DESCRIPTION DS-196013 For most 36-04 Big Twin and 57-03 XL models VALVE SPRING COMPRESSOR TOOL • Necessary for removing or installing valves and springs • Made in the U.S.A. PART # DESCRIPTION 3801-0065 For 05-17 Twin Cam (except SE models), 04-21 XL (except 21 Sportster S/RH1250S) and Buell (except 1125R) VALVE SPRING COMPRESSOR • Used to remove and replace valve and new-style conical valve spring • Requires the use of tool PART #DS-196013 (available separately) • Made in the U.S.A. PART # DESCRIPTION 3801-0317 For 17-21 M-Eight models VALVE SPRING COLLAR • For use with JIMS existing valve spring compressor PART #DS-196013 (sold separately) • Valve spring collar allows existing compressor to remove smaller valves on M-Eight engines • Made in the U.S.A. PART # DESCRIPTION 3801-0366 For 17-21 M-Eight models “ON BIKE” VALVE SPRING COMPRESSOR TOOL • Eliminates the need to remove the cylinder head from the engine when changing valve springs or replacing leaking valve seals • Simply remove the rocker box covers and rockers arms to install compressor on the rocker arm shaft • Once the cylinder is filled with compressed air, easily rotate the tool and compress the top collar of the valve spring, exposing the keepers to remove the top collar, valve spring and seal • Dramatically saves time • Made in the U.S.A. PART # DESCRIPTION FOR 17-20 SOFTAIL AND TOURING MODELS 3801-0355 Balancer bearing removal tool 3801-0356 Balancer bearing install tool BALANCER BEARING REMOVAL/INSTALLER TOOLS • Installer aligns to the crankcase via case bolt and dowel locations; allows installation of bearings without the use of a driver or press • Easily removes the balancer bearings in both Touring and Softail models without damage to crankcase • Made in the U.S.A. 3801-0355 3801-0356
RkJQdWJsaXNoZXIy NDI5NTY=