BOLD MAGENTA part numbers are new for 2024 ELECTRICAL PARTSCANADA.COM ATV/UTV | 2024 737 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. FITS MODEL PART # KAWASAKI KVF650 Brute Force 4x4 05-13 2102-01461 KVF650 Prairie 03-07 2101-0058 KVF700 Prairie 03-07 2101-0058 KSV750 Brute Force 05-10 2102-01461 YAMAHA YFM660 Rhino 04-07 2101-0094 1 For carbureted models only. DYNA FS NON-PROGRAMMABLE IGNITION SYSTEMS •Improved timing curves with high rev limit •Removed reverse rev limit •Overrides belt indicator for full performance at all times •Increased spark energy and throttle response •Easier starting •Plug-in module replacement is easy to mount 2101-0094 2102-0146 DESCRIPTION PART # Rear electrical wiring harness 2120-1046 REAR ELECTRICAL WIRING HARNESS FOR ALL HONDA TALON 19-21 • Allows for easy wiring of any LED lights, brake light, license plate light, or powered LED lighted whip •Simple one-minute install; a true plug-and-play accessory with no cutting required •Can be plugged into each taillight for additional accessories •Recommended for low current lights or to trigger a relay for larger high power lights Warning! Do not overload the vehicle’s electrical system. If circuit is overloaded it could cause the fuse to blow or damage the OEM wiring. DESCRIPTION PART # Pulse busbar pigtail harness 2130-0360 PULSE BUSBAR PIGTAIL HARNESS FOR ALL POLARIS UTV 18-23 •Allows the customer to easily tie into constant or key-on-power for most all aftermarket electrical accessories without cutting factory wiring • Commonly used for light bars, whips, light pods, sound bars, horns, winches (key-on-signal) • Utilizes 14 AWG wire with a 6” lead •Wire colors follow suit with traditional red – constant +12V, orange – key-on +12V, black – ground •Convenient 3-pack for future accessories DESCRIPTION PART # Bus bar 2120-1041 BUS BAR •Alleviates multiple connections to battery terminals by allowing you to connect various power accessories •Base and cover material is made of polycarbonate •Stainless steel #304 studs allow for excellent electrical contact •Bus material made of tin-plated solid copper for maximum conductivity and resistance to corrosion • Continuous amperage of 130 amps AC, 150 amps DC • Maximum voltage rating 300 volts AC, 48 volts DC •Available in seven-position style SWITCH WATT/FUSE PART # Round lighted On/Off switch 300-watt/40-amp 2050-0405 Rectangular lighted On/Off/On switch 300-watt/40-amp 2050-0406 Round lighted On/Off switch 350-watt/40-amp 2050-0407 AUXILIARY LIGHT WIRING HARNESSES • PART #2050-0405 features 6’ long 16 AWG leads with 2-pin connectors, for 2-wire LED lights • PART #2050-0406 features 6’ long 14 AWG leads with 3-pin connectors, for 3-wire LED lights such as models with DRL • PART #2050-0407 features 6’ long 16 AWG leads with 2-pin connectors; for two different 2-wire LED lights 2050-0406 2050-0407
RkJQdWJsaXNoZXIy NDI5NTY=