WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2024. SECTION 15 1152 See OLDBOOK For Early Model Applications WARNING: ALL TANKS ARE SHIPPED UNPAINTED. CAPS ARE NOT INCLUDED UNLESS NOTED.ALL GAS TANKS SHOULD BE FITTED, PRESSURE-TESTED AND SEALED BEFORE BEING PAINTED TO ELIMINATE POTENTIAL PROBLEMS. Side profile PART # DESCRIPTION DS-391226 2.9-gallon rubber-mount tank for 95-03 XL DS-391225 2.25-gallon rubber-mount tank for 95-03 XL PART # DESCRIPTION DS-391224 2.25-gallon rubber-mount tank for 86-94 XL DS-391223 2.9-gallon rubber-mount tank for 86-94 XL GAS TANKS •Bolt-on gas tanks for XL models are made of heavy-gauge steel with reinforced seams •Comes complete with extra-strong mounting tabs •2.9-gallon tanks are 2” wider than stock tanks •All use 22mm petcocks sold separately NOTE: When this gas tank is installed on 92 and later models and the Original Equipment continuous venting system is eliminated or disconnected, you may not reuse your stock vented cap, but may replace it with an earlier version of the screw-type caps. NOTE: 86-94 tanks have petcocks on the right side, 95-03 tanks have petcock on left side. PART # DESCRIPTION 0701-0705 Single cap WASP-STYLE GAS TANK •Wasp-style narrow gas tank for custom applications that have a great vintage look •Made from precision steel stampings and holds 2.2 gal. •Has a right side 3/8” NPT and left side 1/4” NPT petcock bung •Universal brackets make it easy to mount it to any stock or custom frame •Available in a single-cap version •Uses 73-81 style cam lock caps •Tank dimensions: 17.75” L x 9” W x 9 D, tunnel measures 2.5” W x 3.5” D PART # DESCRIPTION 0701-0703 For 95-03 XL 2.9 GALLON KING TANK FOR SPORTSTER •Great looking ‘Old School’ tank •Attaches to the stock frame mounting points •Made from high-quality 18-gauge AKDQ special deep draw material •Accepts all 22mm H-D® or aftermarket petcocks and L96-21 style screw-in gas caps •Made in the U.S.A. NOTE: Paughco recommends all tanks be mounted on leather spacers or bushings. NOTE: All tanks are pressure-tested and are bare metal; fit before painting. PART # DESCRIPTION 0704-0009 Weld-on gas/oil tank mount kit WELD-ON GAS/OIL TANK TAB • Laser-cut 1/4” steel tabs are a great way to mount a custom gas or oil tank •Kit includes two steel tabs and four rubber grommets •Each tab measures 5.9” L x 1.18” W; two .83” holes are spaced 4.58” center-to-center; 1/4” thick •Made in the U.S.A. PART # DESCRIPTION DS280459 Non-vented DS280458 Vented REPLACEMENT GAS TANK BUNGS •Weld-in style bungs used for custom-mounting filler hole in fuel tanks •Accepts 84-E96 screw-in gas caps •Sold each DS280458 DS280459 DS-391224
RkJQdWJsaXNoZXIy NDI5NTY=