WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2024. 533 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. COMPLETE KIT PART # MAXIMUM RECOMMENDED LIFT SEAT PRESSURE COIL BIND RETAINERS FOR 99-04 TWIN CAM AND 86-04 XL WITH 5/16” VALVES 115069 .600” 155@1.875”/175@1.825” 1.080” Steel HIGH-PERFORMANCE VALVE SPRING KIT •Available with steel retainers •Manufactured from ultra-clean high-silicon/vanadium Kobe alloy wire •1.375” top retainers for better clearance inside rocker covers PART # DESCRIPTION DS-199739 For 99-04 Twin Cam and 86-03 XL Evolution HIGH-LIFT VALVE SPRING KIT •Accommodates cam lifts of .550”+ •Installation does not require machining of heads •Kit includes four inner and four outer springs •For use with titanium upper spring collars •Collars sold separately •Made in the U.S.A. PART # DESCRIPTION FOR 05-17 88”/96”/103” TWIN CAM, 04-22 XL (EXCEPT RH SPORTSTER), 09-12 XR 1200 0926-1468 7°, 7mm valve stem w/ stock triple keeper groove (includes steel retainers) 0926-3323 7°, 7mm valve stem w/ stock triple keeper groove (includes titanium retainers) PART # DESCRIPTION FOR 99-04 TWIN CAM AND 86-03 XL 0926-1467 7°,5/16” valve stem w/ stock keeper groove (includes steel retainers) 0926-3322 7°,5/16” valve stem w/ stock keeper groove (includes titanium retainers) ECONO BEEHIVE® VALVE SPRING KITS •Made from premium stress-relieved conical ovate wire •Feature extremely high-level of fatigue life •Use a much smaller and lighter weight retainer to reduce valve weight and create quicker rev and smoother motion •Designed to handle the demands of performance engines with .585” and smaller lift camshafts •Available for 5/16” and 7mm valves •PART #s 0926-1467 and 0926-1468 include Econo BeeHive® valve springs, lightweight 7° steel retainers, machined heat-treated chromoly spring seats, seat shims, valve locks and a set of premium Viton® valve seals equipped with spring-loaded valve stem wiper system •PART #s 0926-3322 and 0926-3323 include Econo BeeHive® valve springs, lightweight 7° Ti retainers, machined heat-treated chromoly spring seats, seat shims, valve locks and a set of premium Viton® valve seals equipped with spring-loaded valve stem wiper system •Seat lb./installed height; 183 lb. at 1.760” (0.510” lift), 175 lb. at 1.785” (0.535” lift), 172 lb. at 1.803” (0.553” lift), 165 lb. at 1.825” (0.574” lift), 163 lb. at 1.835” (0.585” lift), 380 lb. at 1.250” OPEN HEIGHT coil bind at 1.180” •Dyno proven and track tested •Feuling® BeeHive® valve springs must be installed at the correct OPEN HEIGHT, matching max lift to the open height spec of the valve springs •Made in the U.S.A. NOTE: Econo BeeHive® kits are direct replacement with no machining or rocker box clearance required for cams up to .574” lift for 99-04 Big Twin and 86-03 XL and up to .585” lift for 05-17 Twin Cam. 0926-3323 0926-1467
RkJQdWJsaXNoZXIy NDI5NTY=