WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2024. 537 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION FOR 99-17 TWIN CAM (EXCEPT 17 DRESSERS), 86-22 XL (EXCEPT RH SPORTSTERS), 09-12 XR 1200, 94-09 BUELL MODELS (EXCEPT 1125R) 0927-0015 Roller rocker arms (stock 1.625 ratio) (set of 4) 0927-0028 Roller rocker arms (1.725 ratio) (set of 4) 213972 Roller shaft (ea.) 0927-0001 Roller rocker rebuild kit FORGED ROLLER ROCKER ARMS •Forged from 8620 steel, heat-treated then shot-peened for additional strength and durability •Rocker arms have .75” long bushings instead of the .50” long bushings found on most other rocker arms •Feature a modified lubrication system with unrestricted roller oiling •Must be used with adjustable pushrods; sold separately •For ease of adjustment on 91-03 XL and Buell models, use pushrod tube covers PART #DS-193829 •Recommended that new rocker shafts be used when installing roller rocker arms; available separately •Made in the U.S.A. PART # DESCRIPTION 0927-0014 For 99-17 Twin Cam and 86-22 XL (except RH Sportsters), 09-12 XR 1200, 94-09 Buell models (except 1125R) FORGED STANDARD ROCKER ARMS •An economical solution for stock rebuilds, and mild performance upgrades •Forged from 8620 steel for greater strength than stock or cast steel •Feature the same .750” long rocker shaft bushings as S&S Roller Rockers: longer bushing provides 50% more load bearing area; eliminates the risk of engine damage associated with failed needle bearings •Valve contact tips are induction hardened for extended durability •Recommended for cams of .585” lift or less •Sold in set containing two each of front and rear arms •Made in the U.S.A. PART # DESCRIPTION FOR 99-17 TWIN CAM (EXCEPT 17 DRESSER), 86-22 XL (EXCEPT RH SPORTSTER), 09-12 XR 1200 AND 94-09 BUELL (EXCEPT 1125R) DS-193833 Front intake/rear exhaust DS-193834 Front exhaust/rear intake REPLACEMENT ROCKER ARMS WITH BUSHINGS •OEM-style rocker arm •Sold each PART # DESCRIPTION DS-193820 For 99-17 Twin Cam, 86-21 XL (except RH Sportster) and 94-09 Buell (except 1125R) motors; repl. OEM #17611-83 ROCKER ARM SHAFT •Sold each •Made in the U.S.A. PART # DESCRIPTION FOR 17-21 M-EIGHT ENGINES 0927-0034 Rocker arm shafts with hardware kit PART # DESCRIPTION FOR 17-21 M-EIGHT ENGINES (CONT) 0927-0035 Rocker arm shafts only; repl. OEM #17300059A ROCKER ARM SHAFT KITS •Shafts are precision-machined from a low alloy nickel, chromium, molybdenum case-hardened steel •Hardware flats on the end of the shafts are held to a 0.0005” parallel tolerance, ensuring the rocker is seated in the correct position with the pushrod cup and valve stem tip •PART #0927-0034 includes a stud and nut kit to replace the stock hardware used to secure the rocker shafts •Made in the U.S.A. DS-193833 DS-193834 0927-0015 0927-0001 0927-0034 0927-0035
RkJQdWJsaXNoZXIy NDI5NTY=