WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2024. 565 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION EMIS* FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0113 26H chain-drive cam kit 3 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) DS199117 TW26 gear-drive cam kit 3 DS-199179 TW26A chain-drive cam kit 3 PART # DESCRIPTION EMIS* FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0115 37H chain-drive cam kit 3 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) DS-199180 TW37 chain-drive cam kit 3 PART # DESCRIPTION EMIS* FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) DS-199176 TW21 chain-drive cam kit 3 PART # DESCRIPTION EMIS* FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0598 TW48 chain-drive cam kit 3 PART # DESCRIPTION EMIS* FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0278 54H chain-drive cam kit 3 PART # DESCRIPTION EMIS* FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) DS-199178 TW55 chain-drive cam kit 3 PART # DESCRIPTION EMIS* FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0668 57H chain-drive cam kit 3 CAMS FOR TWIN CAM •Andrews Products grinds its cams with the help of a computer with cam design capabilities •Superior technology gives the utmost in both performance and reliability •Only the best alloy steel billets and heat-treating processes are utilized •Harley’s Twin Cam engine power can be made even more convincing when superior Andrews computer-designed high-performance cams are installed •Made in the U.S.A. NOTE: All Andrews gear-driven cams require four-gear set for installation (DS-199532 for 99-06 applications; 0925-0166 or 0925-0152 for 07-17 Twin Cam and 06 Dyna applications). NOTE: Chain Driven Cams: 00-06 model cams use a splined cam drive sprocket. These cams will fit in the 1999 Twin Cam motor, but the splined cam drive sprocket OEM #25716-99 or DS-199175 must be used. NOTE: Installer must check coil bind, valve-to-valve clearance and valve-to-piston clearance. CAMS FOR TWIN CAM continued on next page. 26 SERIES GRIND CAMS •Bolt-in cam for lower rpm torque on heavier bikes •For two-up touring •Good power from 1800-5500 rpm •Can be used with stock springs and tappets •Works well with carbs or fuel injection TW48 SERIES GRIND CAMS •Broad tip cams for baggers with stock motors; max torque at low and mid rpm ranges •Use stock springs 55 SERIES GRIND CAMS •Cams for maximum torque and horsepower at higher rpm ranges (2600-6000+ rpm) •Designed for engines with 9.5:1 compression ratio or higher with 88”-95” •Coil bind must be checked, but stock tappets can be used 57 SERIES GRIND CAMS •Bolt-in broad tip cams; 96”, 103” Limited and 110” CVO engines •Cams work best at rpm range of 2200-5600 21 SERIES GRIND CAMS •Bolt-in cam for more torque with stock compression •Run best with low-restriction exhausts (1700-5200 rpm) •Similar to the EV-23 cam •Cams work well with fuel injection or carburetor models •Can be used with stock valve springs and tappets •Works well with carbs or fuel injection 37 SERIES GRIND CAMS •Bolt-in cams •Smooth idle with broad torque band •Run best with low-restriction exhausts (2200-5800 rpm) •Can be used with stock valve springs and tappets •Works well with carbs or fuel injection 54 SERIES GRIND CAMS •Designed for 96” and 103” motors with up to 10:1 compression ratio •Cams work best at rpm range of 2200-5600 DS-199176 0925-0113 DS199117
RkJQdWJsaXNoZXIy NDI5NTY=