WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2024. SECTION 7 572 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION EMIS* 0925-1067 For 07-17 Twin Cam, 06 Dyna 4 HYDRAULIC CAM CHAIN TENSIONER PADS •Tensioner pads are a direct drop-in replacement for the factory cast tensioner housings as well as the billet Feuling tensioner housings •Pads are injection molded Nylon with PTFE added to increase wear and friction resistance •Tensioners are single piston, duplicating the output pressure of stock units •Replacement pads include new hydraulic lash units •Fit inner and outer factory HD cast housings and Feuling billet housings •Sold in pairs •Made in the U.S.A. PART # DESCRIPTION 0925-0147 Roller conversion cam sprocket ROLLER CONVERSION CAM SPROCKET •34 teeth with ignition trigger ring •Must use with 99-01 engines with stock ignition and cam position sensor •02-06 engines can use stock rear cam drive sprocket •Trigger ring required for 99-01 engines with rear cam drive sprockets to permit engine control system to function correctly •For use with Andrews Twin Cam Conversion Chain Driven Cams; see page 566 •Made in the U.S.A. PART # DESCRIPTION EMIS* FOR 17-23 M-EIGHT, 07-17 TWIN CAM MOTORS 0925-1058 Crankshaft cam drive sprocket, 17 tooth; repl. OEM #25673-06 4 FOR 07-17 TWIN CAM MOTORS 0925-1059 Cam drive sprocket (Twin Cam only), 34 tooth; repl. OEM #25728-06 4 FOR 99-01 TWIN CAM MOTORS 0925-1371 Rear cam outer chain sprocket for engines with Magneti Marelli ignition using updated hydraulic chain drive system with 07-17 style outer chain, 34 tooth 4 0925-1370 Rear cam outer chain sprocket for engines with Magneti Marelli ignition using factory 99-06 style outer chain, 34 tooth 4 CAM CHAIN DRIVE SPROCKETS •Machined steel, stock replacement roller chain drive sprockets fit 07-17 Twin Cam engines as direct replacements and work on early 99-06 engines when upgrading to the hydraulic cam chain tensioners using the roller chain •Made in the U.S.A. PART # DESCRIPTION 0925-0951 For 17-23 M-Eight, 07-17 Twin Cam models and 06 Dyna; repl. OEM #25729-06 CAMSHAFT SPROCKET SPACING ALIGNMENT/THRUST WASHER KIT •Fits stock and stock replacement camshafts and conversion camshaft upgrades on 99-06 engines to the hydraulic chain tensioner system •Conversion camshafts use the late 07-17 style camplate and oil pump •Alignment washers are used to align the rear camshaft sprocket with the crank sprocket to achieve correct chain alignment •Kit includes front cam thrust washer .100”, rear cam sprocket alignment washers .110”, .120”, .130”, .140” and .150” •Made in the U.S.A. NOTE: Not for 2023 models with 121” VVT motors. PART # DESCRIPTION EMIS* 0925-0950 For all 99-06 Twin Cam motors (except 06 Dyna Glide); repl. OEM #25285-08 4 CAMSHAFT SPROCKET ALIGNMENT SPACER KIT •Spacers fit stock and stock replacement early style camshafts and conversion cam plates which update the early style camshafts to the late style hydraulic tension system •Conversion cam plates use the original style 99-06 camshafts with the original style silent chain in the rear •Spacers are used to align the rear camshaft sprocket with the crank sprocket to achieve correct chain alignment •Kit includes one each of the following thickness spacers: .297”, .307”, .317”, .327”, .337”, .347” and .357” •Made in the U.S.A. PART # DESCRIPTION EMIS* 0925-1066 Hydraulic tensioner kit, inner/outer, 07-17 Twin Cam, 06 Dyna, chain drive and camplate 4 0925-1064 Hydraulic tensioner, outer, 07-17 Twin Cam, 06 Dyna, chain drive and conversion camplate (ea.) 4 0925-1065 Hydraulic tensioner, inner, 07-17 Twin Cam, 06 Dyna, chain drive and conversion camplate (ea.) 4 HYDRAULIC CAM CHAIN TENSIONER ASSEMBLIES •Stock replacement hydraulic cam chain tensioners •Tensioner housings are precision machined from billet 6061 aluminum, pads are injection molded nylon with PTFE added to increase wear and friction resistance •Tensioners are single piston duplicating the output pressure of stock units •Feuling tensioners include ARP® 12-point hardware •Tensioners fit Feuling, factory and SE 07-17 camplates and conversion camplates designed to run the early 99-06 camshafts •Made in the U.S.A. PART # DESCRIPTION EMIS* FOR 17-23 M-EIGHT, 07-17 TWIN CAM, 06 DYNA AND CONVERSION CAMPLATES/CAMSHAFTS 0925-0954 Outer roller chain, 22 link; repl. OEM #25675-06 4 FOR 07-17 TWIN CAM, 06 DYNA AND CONVERSION CAMPLATES/CAMSHAFTS 0925-0953 Inner roller chain, 16 link (Twin Cam only); repl. OEM #25683-06 4 PART # DESCRIPTION EMIS* FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-0955 Inner silent chain, 16 link; repl. OEM #25607-99 4 0925-0956 Outer silent chain, 22 link; repl. OEM #25610-99 4 CAM CHAINS •Stock replacement chains •Made in the U.S.A. 0925-0954 0925-0955 0925-1058 0925-1059 0925-1370 0925-1371
RkJQdWJsaXNoZXIy NDI5NTY=