WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2024. SECTION 7 578 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 0932-0192 For 17-23 M-Eight HIGH FLOW CAMPLATE FOR M-EIGHT •Increases engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages including the scavenging return holes from the pump to the camplate and into the engine case •Camplate matches the oil portholes on the camplate to the oil holes in the engine case to increase oil flow throughout the engine •Lowers engine temperatures by 15-25 degrees and oil running temperature by 15-25 degrees when matched with a Feuling HP+ or RS oil pump •7075 billet aluminum construction, which is 50% harder and stronger than the factory cast and Feuling® OE+ camplates •Increases the strength and hardness of the camplate, holding tighter tolerances under temperature and eliminating flexing and the need for bronze bushings •When matched with the Feuling® Race Series Oil Pump, rear wheel power gains of 2 horsepower and 2 ft./lb. of torque can be achieved •For gear or chain drive cams (block-off plate PART #0932-0036 required when using gear drive cams) •Made in the U.S.A. NOTE: For use ONLY with Feuling HP+ and Race Series M-Eight oil pumps. PART # DESCRIPTION EMIS* FOR 07-17 TWIN CAM (AND 06 DYNA) 0925-08421, 5 For chain or gear drive cams 4 FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-08392 For gear drive cams 4 PART # DESCRIPTION EMIS* FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) (CONT) 0925-08402, 3 For chain drive cams w/ spring tensioners 4 0925-08414 Hydraulic tensioner conversion camplate for stock chain drive cams 4 OE+ CAMPLATES FOR TWIN CAM •Billet camplates are manufactured from 6061 aluminum providing increased rigidity and machined to Feuling® high tolerance standards •Designed and manufactured to the highest standard of quality with proven Feuling® performance •The pressure relief valve and spring are pre-set, matched and seated by Feuling® with a full pop off pressure of 50-60 psi •Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerance for improved press fit •Bearing retainer plate and hardware included •Camplate for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal bore tolerance for improved cam fitment •Added cam journal oil groove for cold start up protection and increased cam journal lubrication 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 For use with factory or any Twin Cam oil pump with the 99-06 bolt pattern. Compatible with Feuling oil pump PART #s 0932-0018, 0932-0089 or 0932-0020. 3 Includes tensioner pins and hardware guide. 4 Requires 07-17 style oil pump, hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kits PART #s 0925-1069 or 0925-1070. Compatible with Feuling oil pump PART #s 0932-0090, 0932-0023 or 0932-0026. 5 For use with factory and or any Twin Cam oil pump with ‘07-’17 bolt pattern; compatible with Feuling oil pump PART #0932-0090, 0932-0023, 0932-0026. •Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear •Made in the U.S.A. 0925-0839 0925-0842
RkJQdWJsaXNoZXIy NDI5NTY=