WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2024. 579 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION EMIS* 0925-0110 For 07-17 Twin Cam and 06 Dyna 4 HIGH FLOW CAMPLATE FOR TWIN CAM •Increase engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages •Camplate matches the oil port holes throughout the camplate to the port holes in the engine case increasing engine oil flow throughout the engine •25-35 degree cooler engine temperatures and 20-30 degree cooler oil temperatures •Made from 7075 billet aluminum which is 50% harder and stronger than the factory, SE® and other aftermarket camplates •The 7075 increases the strength and hardness of the camplate, holding tighter tolerances under temperature eliminating flexing and the need for bronze bushings •Camplate is pressure tested and pressure relief valve is seated, sealed and set to pop off at 55-60 psi •When matched with the Feuling® Race Series oil pump rear wheel power gains of 3 Horsepower and 4 ft/lbs of Torque can be achieved •For use ONLY with the Feuling® oil pumps •For chain or gear drive cams •Bearing and retainer plate hardware is included •Camplate has tighter cam journal tolerance for improved cam fitment •Added cam journal oil groove for cold startup protection and increased cam journal lubrication •Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear •Made in the U.S.A. NOTE: Block-off plate PART #0932-0036 required when using gear drive cams. NOTE: Requires the use of 07-17 style Feuling HP+ or Race Series oil pump PART #s 0932-0023 or 0932-0026. PART # DESCRIPTION 0925-0914 For 07-17 Twin Cam and 06 Dyna models CAMPLATE FOR TWIN CAM •Precision CNC-machined forged aluminum •Adjustable oil pressure regulator; adjust without removing plate from the engine •Passage plugs are removable for service •Rebuildable bronze pinion shaft bushing in all models and bronze cam bushings in 07-later style •Made in the U.S.A. NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. PART # DESCRIPTION 0932-0036 For 17-23 M-Eight, 07-17 Twin Cam and 06 Dyna camplates BLOCK-OFF PLATES •Block-off hydraulic chain tensioner holes when using gear-driven cams •Made in the U.S.A. PART # DESCRIPTION 2401-09931 For 17-23 M-Eight engines w/ Feuling high flow camplate and HP+ or Race Series oil pumps (do not use washers with ARP® oil pump bolts) PART # DESCRIPTION 2401-0127 For 99-17 Twin Cam engines w/ Feuling HP+, Race Series or OE+ camplates and oil pumps 1 Not for use with OE+ camplates/oil pumps. CAMPLATE/OIL PUMP FASTENER KITS •Optional kit for Feuling camplates/oil pumps only •Quality 12-point, heat-treated 8740 chromoly steel bolts with black oxide finish manufactured by ARP® to Feuling’s exact specifications •Precision-rolled threads provide optimum engagement, prevent galling and promote consistent torque loading •Wide, underhead flange design provides even load distribution for optimum sealing of surfaces to prevent leaks •Tensile strength rated at 170,000 psi; superior and stronger than OEM and stronger than grade 8 fasteners •Includes moly assembly lubricant for installation •Made in the U.S.A. 2401-0127 2401-0993
RkJQdWJsaXNoZXIy NDI5NTY=