WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2024. SECTION 7 588 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 0932-01061 For 07-17 Twin Cam and 06 Dyna models 1 Will not fit 00-02 Softails when used with a TC3 cam plate. TC3 OIL PUMPS FOR TWIN CAM •Three stages for consistent pressure and reliable scavenging •Separate scavenge sections for flywheel cavity and cam chest (no interface) •Screens and magnetic traps help protect the scavenge rotors from debris •Special design allows S&S pumps to tolerate more pinion shaft run-out without damage •Made in the U.S.A. NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. PART # DESCRIPTION 0932-0088 For 07-17 Twin Cam and 06 Dyna models 0932-0087 For all 99-06 Twin Cam (except 06 Dyna models) HIGH-PERFORMANCE TWIN CAM OIL PUMPS •Helps to reduce oil carryover during high rpm operation; higher volume helps reduce engine and oil temperatures •53mm diameter rotors for maximum performance •Gain of 20% oil pressure, 125% pressure volume and 135% scavenge volume over OEM stock TC88 oil pumps •Gain of 16% oil pressure, 66% pressure volume and 100% scavenge volume over OEM stock TC96/103 oil pumps •High-quality die-cast aluminum body construction, high-strength steel gear construction •Fits both stock and aftermarket cam support plates for seamless installation NOTE: Does not fit Screamin’ Eagle cam plate. PART # DESCRIPTION 0932-0236 For 17-23 M-Eight air-cooled motors HIGH-PERFORMANCE M-EIGHT OIL PUMP •126% feed and 131% scavenge volume compared to OEM (stock) M-Eight fourth generation oil pumps at 1000 rpm •123% feed and 146% scavenge volume compared to OEM (stock) M-Eight fourth generation oil pumps at 2500 rpm •Scavenge side discharge was improved by modifying the suction ratio to help eliminate sumping from excess oil in the crankcase •Improved oil flow by inserting an oil passage correction spacer between the large-capacity oil pump body and the cam support plate PART # DESCRIPTION 0932-0189 For 91-22 XL (except RH Sportster) OIL PUMP ASSEMBLY •High-quality replacement cast aluminum pump body with steel gears and shaft •Raw cast-aluminum finish •Gaskets and seals included PART # DESCRIPTION 0932-0019 For Feuling® oil pump PART #s 0932-0018 and 0932-0020 0932-0024 For Feuling® oil pump PART #s 0932-0023 and 0932-0026 OIL PUMP REBUILD KITS •Include everything needed to rebuild Feuling® HP+® and Race Series oil pumps •Kit comes with new O-rings, separator plate and installation instructions •Made in the U.S.A. PART # DESCRIPTION 0932-0288 For 17-23 M-Eight OIL CONTROL VALVE FOR M-EIGHT •Constructed of 6061 billet aluminum with a high-strength steel check ball retainer for long-lasting durability •Helps ensure engine properly regulates the amount of oil flow to oil cooler and heads •Easy installation •Made in the U.S.A. 0932-0088 0932-0019
RkJQdWJsaXNoZXIy NDI5NTY=