WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2024. SECTION 10 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 710 PART # DESCRIPTION 2101-0033 For carbureted 99-03 Twin Cam models DYNA 2000TC PROGRAMMABLE DIGITAL PERFORMANCE IGNITION MODULE •Single-fire, fully programmable performance ignition •Sixteen programmable advance curves in three groups: stock-to-slightly-modified motors, heavily-modified motors and insanely-modified motors •Eight rev limiter settings in 250 rpm steps from 5750-7250 rpm •All functions offer full digital accuracy •Compatible with stock and performance coils – less than 1-ohm resistance •Coil current constantly monitored to provide constant full-spark energy •Uses all stock sensors and connectors •Built-in reverse battery and spike protection •Data recording includes total engine hours, time wide-open throttle, longest time operating at wide-open throttle, max rpm, seconds near rev limit and number of engine starts •PC programmability makes possible an eight-point, fully definable, wide-open throttle curve and a fully definable part-throttle curve, programmable rev limit in 50 rpm steps, 0-5 programmable dead-cranking revs, total of +/- 10° rear cylinder offset, programmable rev limiter, and security lock-out (pin # activated) •Made in the U.S.A. PART # DESCRIPTION PLUG-IN IGNITION MODULES 2101-0034 For 04-06 Twin Cam and Sportster carbureted models w/ a single 12-pin connector DS242377 For 99-03 Twin Cam carbureted models w/ two 12-pin connectors 2101-02191 For 99-03 Twin Cam carbureted models w/ two 12-pin connectors and two-stage rev limiter (race only) OPTIONAL ACCESSORIES 2101-0075 USB interface 1 Requires USB interface (PART #2101-0075) to program. PLUG-IN IGNITION MODULES •Features two advance curve families that are adjustable to accommodate stock and modified engines •Selectable multi-spark mode for quick starting and smooth cruising •Four rotary switches for mode select, timing adjustments, advance slope and rpm limit (in 100 rpm steps) •Coil outputs protected against short circuits •Requires OEM coils with less than 1 ohm primary resistance and low-resistance spiral-core or carbon-core suppression-type plug wires •12V power adapters are used to power up the modules when removed from the bike (sold separately) •Optional USB interface (PART #2101-0075) and software required for programming custom curves (programs available on website www.daytona-twintec.com/index.html) •Includes easy-to-follow instructions •Made in the U.S.A. NOTE: Will not work on fuel-injected models. NOTE: Exempt per CARB Executive Order (E.O.) #D-641-1. PART # DESCRIPTION 2101-0063 For carbureted 04-06 Twin Cam models PART # DESCRIPTION 2101-0071 For 04-06 XL DYNA 2000TC-3 DIGITAL PERFORMANCE IGNITION MODULES •Module has a single connector •Loaded with 16 different advance curves, giving engine builder a wide range of curves to work with •Adjustable rev limiter allows the user to select a rev limit ranging from 5750 to 7500 rpm in 250 rpm steps •Made in the U.S.A. 2101-0063 2101-0071 2101-0034 2101-0075 2101-0219
RkJQdWJsaXNoZXIy NDI5NTY=