WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 10 All part numbers in BLUE are new for 2024. See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 753 PART # DESCRIPTION COMPLETE KIT 2106-0221 For 99-13 FLHTC, FLHTCU, FLHX REPLACEMENT SWITCHES 2106-0232 Spotlight switch; repl. OEM #71505-96 2106-0233 Speaker switch; repl. OEM #77092-98 PART # DESCRIPTION REPLACEMENT SWITCHES (CONT) 2106-0219 Accessory switch; repl. OEM #71535-96 REPLACEMENT MOUNTING BRACKET 2106-0222 Mounting bracket; repl. OEM #71434-96B INNER FAIRING CAP SWITCH KIT •Kit includes all four switches: spotlight/driving light switch, speaker switch, cruise control switch and accessory switch PART # COLOR 2106-0011 Stainless steel PART # COLOR 2106-0418 Gold PART # COLOR 2106-0419 Black MINI PUSH-BUTTON SWITCHES •12mm round push-button switch includes a special radius-shaped spacer to allow mounting in handlebars •Great for turn signal, starter, horn, stop or hi-low operations (must be used with a relay) •Includes two 20” wires; installing requires 9/32” drill and 5/16” UNF tap •Sold each PART # DESCRIPTION 2106-0220 Protective boot for toggle switch; repl. OEM #74408-89A SPOTLIGHT/ACCESSORY TOGGLE SWITCH BOOT •Direct OEM replacement boot PART # DESCRIPTION 2130-0349 For all 16-23 H-D Throttle-By-Wire models PART # DESCRIPTION 2130-0348 For all 14-15 H-D Throttle-By-Wire models PART # DESCRIPTION 2130-0347 For all 08-13 H-D Throttle-By-Wire models REPLACEMENT TWIST GRIP SENSORS •Pre-installed terminals that utilize MIL-SPEC crimping presses •Hardwired, like OEM CVO versions, from the sensor to the main connection on the harness •100% plug-n-play •PART #2130-0347, sensor includes HD #72188-07BK male 6-position connector for installation after the harness is routed through the handlebar •PART #2130-0348, sensor includes OEM #72414-07BK female 6-position connector for installation after the harness is routed through the handlebar •PART #2130-0349, sensor includes installed OEM #69201162 micro-connector for easy installation after routed through the handlebar •Additionally includes an installed male 2-position heated grip connection OEM #72902-01BK, which is NOT installed to place wiring harness through handlebar •Made in the U.S.A. NOTE: Make sure grip is snug against gear drive to prevent damage. PART # DESCRIPTION 2120-1118 For 99-13 FLHS/FLHT/FLHTC/ FLHTCU/FLHTCUL/FLHTCUSE/ FLHTK/FLHTKL/FLHX/FLHXS/FLHXXX PASSING LAMP CONTROL HARNESS •Allows the use of passing lamps while the high beam is on •Plug-n-play installation PART # DESCRIPTION 2120-1114 For 14-23 FLTR/FLHX/ FLHT, 17-21 FLHRXS, 14-17 FXDB/ FLST 2120-1117 For 14-22 FLHR (except 17-22 FLHRXS) PART # DESCRIPTION 2120-1116 For 99-13 FLHR/FLHT 2120-1115 For 06-08 FLHX/FLTR HARNESS TURN SIGNAL TAPS •Front turn signal tap •For adding additional front turn signals • Plug-n-play •Made in the U.S.A. 2120-1115 2120-1116 2130-0347 2130-0348 2130-0349 2106-0011 2106-0418 2106-0419 2106-0221 2106-0222
RkJQdWJsaXNoZXIy NDI5NTY=