BOLD MAGENTA part numbers are new for 2024 EXHAUST PARTSCANADA .COM OFFROAD | 2024 45 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. EXHAUST PIPE SPRINGS •62mm size are stainless steel with a double swivel design •80mm size are zinc-plated steel •Sold in packs of 4 DESCRIPTION PART # 62mm 2404-1024 DESCRIPTION PART # 80mm 2404-1025 EXHAUST SPRINGS •Stainless steel construction gives superior strength and appearance • Swivel hook design eliminates binding, extending spring life •Available for most late-model 2-stroke and 4-stroke models •Sold in pairs •Made in the U.S.A. NOTE: When measuring for exhaust spring length, please use points #1 - #3 for reference. 1. Exhaust springs should be measured when they are off the vehicle.Wear eye protection when removing. 2. The length measurement should be taken from inside hook to opposite end inside of hook. 3. For correct fit, an exhaust spring should not be extended more than 20% of its free length. SPRING LENGTHS LENGTH PART # 38mm M7713 57mm M7714 LENGTH PART # 60mm M7715 63mm M7709 LENGTH PART # 67mm M7710 70mm M7716 LENGTH PART # 75mm M7711 80mm M7717 LENGTH PART # 83mm M7712 90mm M7718 LENGTH PART # 100mm M7720 FITS MODEL LOCATION PART # APRILIA All models (except 250s) Header M7717 GAS GAS 2-strokes 97-15 Pipe M7715 HONDA CR80R 86-01 Pipe M7712 CR80/85R 02-07 Pipe M7718 CR125R 02-07 Pipe M7712 CR250R 86-97 Pipe M7711 CR250R 98-08 Pipe M7712 CR500R 86-98 Pipe M7712 HUSABERG 2-strokes 12-14 Pipe M7714 4-strokes 12-14 Silencer M7715 HUSQVARNA 2-strokes 92-08 Pipe M7716 2-strokes 09-16 Pipe M7711 4-strokes 91-08 Pipe M7717 4-strokes 91-08 Header M7717 4-strokes 09-16 Pipe M7714 FITS MODEL LOCATION PART # HUSQVARNA (CONT) 4-strokes 09-16 Header M7714 KAWASAKI KX60/65 85-16 Pipe M7714 KX80/85/100 89-16 Pipe M7714 KX125 87-89 Pipe M7710 KX125 90-07 Pipe M7714 KDX200/220 89-06 Pipe M7710 KX250/500 84-97 Pipe M7710 KX250 98-00 Pipe M7716 KX250 01-08 Pipe M7717 KX500 98-05 Pipe M7710 KTM SX65 98-16 Pipe M7713 Silencer M7714 2-strokes 85-97 Pipe M7715 2-strokes 98-16 Pipe M7714 4-strokes 98-16 Header M7713 4-strokes 89-16 Silencer M7715 FITS MODEL LOCATION PART # SUZUKI RM60/65 03-07 Pipe M7714 RM80/85 89-16 Pipe M7715 RM100 03-04 Pipe M7714 RM125 84-91 Pipe M7710 RM125 92-08 Pipe M7715 RM250 88-91 Pipe M7710 RM250 92-08 Pipe M7715 RMX250 88-91 Pipe M7710 RMX250 92-98 Pipe M7715 TM 80J 96-12 Pipe M7716 125/250/300 91-16 Pipe M7717 YAMAHA YZ80/85 85-16 Pipe M7711 YZ125/250 89-16 Pipe M7711 WR250 89-97 Pipe M7711 YZ250F/400F/426F/450F 98-16 Silencer M7711 DESCRIPTION PART # Straight section heat shield 1861-0148 STRAIGHT SECTION HEAT SHIELD •Uses the same antiballistic composite material as custom molded pipeguards and includes stainless steel mounting brackets •The straight section heat shield is designed to fit over the section of pipe that contacts your leg and boot •Many aftermarket manufacturers leave out a heat shield – use ours before you ruin your gear • Available in 6” length to fit virtually all 4-stroke headers on bikes and ATVs DESCRIPTION PART # 2-stroke M-610 450 4-stroke (fits pipe diameters 1.5” and larger) 1861-0612 PIPE ARMOR •Privateer-priced pipeguard with works protection •Sturdy armor for your vulnerable and expensive exhaust •3mm aluminum is the thickest pipe protector available for 2-strokes •1/16” thick stainless steel for 4-strokes •Helps prevent power-robbing dents • 24” long for 2-stroke exhausts and 10” long for 4-stroke exhausts • PART #1861-0612 is for pipe diameters 1.5” and up (450 4-stroke) •Made in the U.S.A. M-610 1861-0612 2404-1025
RkJQdWJsaXNoZXIy NDI5NTY=