BOLD MAGENTA part numbers are new for 2024 ENGINE PARTSCANADA .COM OFFROAD | 2024 643 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. HIGH-PERFORMANCE PISTONS (CONT) HIGH-PERFORMANCE PISTONS continued on next page. FITS MODEL BORE (MM) X STROKE (MM) DISP. (CC) BORE SIZE (MM) OVERSIZES (MM) PK KIT PART # PISTON PART # REPL. RING SET PART # REPL. CIRCLIPS PART # (PR.) REPL. WRIST PIN PART # TOP-END BEARING PART # KTM 4-STROKE 250 EXC-F 14-16, 250 XCF-W 13-16 78 250 78.0 STD 0903-1168 - 0912-0120 - 13.9:1 Standard Compression x ArmorGlide 52.30 250 SX-F 13-15 78 250 78.0 STD 0903-1168 - 0912-0120 - 13.9:1 Standard Compression x ArmorGlide 52.30 250 SX-F 16-22, 250 XC-F 16-22 78 250 78.0 STD 0910-6074 - 0912-0120 - - - 14.4:1 Compression x ArmorGlide. Strutted forging 52.30 350 EXC-F/XCF-W 12-16, 88 350 88.0 STD 0903-1140 - - CW18 - - Freeride 350 12-15 x 13:1 High Compression 57.5 350 SX-F 16-18 88 350 88 STD 0910-6075 - - - - - 14:1 High Compression x ArmorGlide 57.5 450 SX-F 16-19 95 449 95.0 STD 0910-6079 - - CW19 0913-0012 - 12.6:1 Compression 16-17, 12.75:1 18-19. x ArmorGlide. Boxed forging 63.4 450SX-F 16-19 95 449 95.0 STD 0910-6080 - - CW19 0913-0012 - 13.5:1 Compression X ArmorGlide 63.4 520 SX/EXC 00-02 95 510 95.0 STD - 0910-0787 - - - - 525 SX/EXC 03-07 x 11:1 Compression 72 Cylinder boring and replating required for oversizes SUZUKI 2-STROKE RM60 03-04 43 60 43.0 STD - 648M04300 - - - - *Electrofusion bore - cylinder sleeving x or replating required for oversizes 41.6 RM65 03-06 44.5 64 44.5 STD - 752M04450 - - - - *Electrofusion bore - cylinder sleeving x or replating required for oversizes 41.6 RM80 83-85 49 82.87 49.0 STD - - - CW14 - B1012 x 44 RM80 86-87 47.5 82 47.5 STD - - - CW14 - B1012 x 46.8 RM80 88-90 47.5 82 47.5 STD - - - CW14 - B1012 x 46.8 RM80 91-01 47.5 82 47.5 STD - 645M04750 - CW14 - B1012 Pro-Lite x 46.8 RM85 02-23 48 84.7 48.0 STD - 806M04800 - CW14 - B1012 Pro-Lite x *Must use stock thrust washers 46.8 RM100 03-04 52.5 99 52.5 STD - 651M05250 - CW14 - B1006 *Electrofusion bore - cylinder sleeving x or replating required for oversizes 45.8 RM125 89-99 54 123 54.0 STD - 641M05400 - CW15 - B1013 Pro-Lite x *SCEM Composite - Cylinder 54 sleeving or replating required for oversizes RM125 00-03 54 124.8 54.0 STD - 754M05400 - CW15 - B1013 Pro-Lite x *SCEM Composite - Cylinder 54.5 sleeving or replating required for oversizes
RkJQdWJsaXNoZXIy NDI5NTY=