BOLD MAGENTA part numbers are new for 2024 ENGINE PARTSCANADA.COM STREET | 2024 HIGH-PERFORMANCE GASKETS AND GASKET KITS continued on next page. 1009 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. FITS MODEL PART # HONDA C125 ABS 19-21 1860-2052 CT125 ABS 21-22 1860-2052 Grom 125 14-19-20/22 1860-2052 Grom 125 ABS 18-20/22 1860-2052 Z125M Monkey 19-21 1860-2052 Z125M Monkey ABS 19-22 1860-2052 CB160 65-69 1860-2050 CL160 65-68 1860-2050 CB175 69-73 1860-2050 CL175 69-73 1860-2050 CM185T 78-79 1860-2050 CB200 74-76 1860-2050 FITS MODEL PART # HONDA (CONT) CL200 74-76 1860-2050 CM200T Twinstar 80-82 1860-2050 CB250 Nighthawk 91-08 1860-2050 CBR250R 11-13 1860-2051 CM250C 82-83 1860-2050 CMX250 85-16 1860-2050 CB300F 15-18 1860-2051 CB300F ABS 17-22 1860-2051 CB300R 19-22 1860-2051 CB300R ABS 19-21 1860-2051 CBR300R 15-20 1860-2051 CBR300RA ABS 15-22 1860-2051 FITS MODEL PART # HONDA (CONT) CMX300 17-22 1860-2051 CMX300 ABS 17-22 1860-2051 GB500 89-90 1860-2050 YAMAHA SR400 15-17 1860-2048 SRX600 86 1860-2049 FZ07 15-17 1860-2049 MT07 18-22 1860-2049 XSR700 18-22 1860-2049 XTZ700 Tenere 22 1860-2049 YZF-R7 22 1860-2049 EXHAUST GASKET KITS • Includes all applicable O-rings, springs, washers and gaskets required for all cylinders 1860-2049 1860-2052 HIGH-PERFORMANCE GASKETS AND GASKET KITS •Gaskets and gasket sets used by professionals in high-performance machines and as OE replacements worldwide •Materials may vary depending on what is correct and engineered for specified application •Each PART # contains the proper amount of gaskets for one application •Made in the U.S.A. HEAD AND BASE GASKETS •Quality materials developed for maximum performance tolerances and longevity; available in several thicknesses and materials •MLS (Mutli-Layer Steel) head gaskets promote an even torque load across the gasket sealing surface utilizing LCE (Load Control Embossments), providing less bore distortion and better piston ring seal for more power • Outer layers are embossed and coated on both sides with Viton® to meet the demands of a variety of harsh sealing environments, load conditions and surface finishes • Center or shim layer is uncoated stainless steel, which can be varied to accommodate multiple thickness requirements •Sold each •Made in the U.S.A. LOWER END KITS •Contains all gaskets and seals needed •Made in the U.S.A. STATOR AND CLUTCH COVER GASKETS •Made from AFM material for longevity •AFM is a compounded nitrile synthetic rubber bonded to an aluminum core with a high temperature resistance of more than 250°F; it has an 85% recovery while maintaining a strong torque retention •No gasket sealants or silicone bead is required, re-torque is also not required •Sold each •Made in the U.S.A. VALVE COVER GASKETS •Made from AFM or thick fiber material depending on application •Sold each •Made in the U.S.A. EXHAUST GASKETS •Exhaust gaskets are made for extreme temperatures •Sold as a set per application •Made in the U.S.A. Head gasket Base gasket Lower end kit
RkJQdWJsaXNoZXIy NDI5NTY=