BOLD MAGENTA part numbers are new for 2024 LIGHTING PARTSCANADA.COM STREET | 2024 603 APOLLO TURN SIGNAL MODULES AND RUN/TURN SIGNAL MODULES •Perfect for custom mounting or molding •Feature a black aluminum ring with smoked lenses and an 8mm mounting stud •Both styles feature two very bright amber SMD LEDs are installed in the center, enabling an extremely small design •The outer ring consists of the new COB technology (Chip On Board), providing the best possible efficiency and service life •Run/turn signal modules include a white daytime running light in the outer ring •COB technology allows higher light values to be achieved than with conventional LEDs •Turn signals are for use as front or rear turn signal •Run/turn signals are for front use • Dimensions: overall depth .50”, depth of center .35”, overall diameter .87”, diameter of center .79”, thread stud: M8 x .47” •Universal fitment for 12V systems • E-approved •Sold in pairs NOTE: The unit can be installed flat without the aluminum ring, leaving only the lens visible. This requires drilling a .79” hole.Alternatively, the unit can be mounted with the aluminum ring on a retaining plate. DESCRIPTION PART # Turn signal modules 2020-2057 DESCRIPTION PART # Run/turn signal modules 2020-20591 1 The Highsider PL Control Box CB2 PART #2050-0472 switches the position light off during the flashing process and goes on again after the flashing process (with a small delay). DESCRIPTION PART # Apollo CNC weld-in housing 2020-2093 APOLLO CNC WELD-IN HOUSING •Made from easily weldable steel •This housing offers custom possibilities to mount the Highsider Apollo lighting series • Dimensions: diameter: .87”, depth: .87”; interior: diameter: .79”, depth: .83”, back hole: .19” •Sold each AKRON-FLASH LED BAR END TURN SIGNALS AND RUNNING LIGHTS/TURN SIGNALS •Offer the perfect solution to relocate turn signals or add additional visibility •The LED light has a horizontal adjustment of up to 26 degrees to place the light where you need it most •Available as turn signals with amber LED lights or as running lights/turn signals that pack a white daytime running light and an amber turn signal into a single unit •CNC-machined aluminum housing and paired with a smoked lens • Pre-wired 40” wire leads ensure adequate length for internal handlebar wiring •Universal for 7/8” and 1” handlebars DESCRIPTION PART # TURN SIGNALS Black 0634-0589 Titan 0634-0590 DESCRIPTION PART # RUNNING LIGHTS/TURN SIGNALS Black 0634-05911 Titan 0634-05921 1 1 The Highsider PL Control Box CB2 PART #2050-0472 switches the position light off during the flashing process and goes on again after the flashing process (with a small delay). • Measures 1.41” in width and 1.35” in diameter • Cable length: approx. 40” •Universal fitment for 12V systems • E-approved •Sold in pairs NOTE: Not for use as a bar end mirror mount. DESCRIPTION PART # Apollo run/turn/brake signal modules 2020-2103 APOLLO RUN/TURN/BRAKE SIGNAL MODULES •Built for custom mounting in multiple locations •Includes a black aluminum ring with smoked lenses •Center of light features two ultra-bright SMD LEDs •Outer ring consists of COB LEDs (Chip On Board) •The semiconductors are bonded directly to a printed circuit board •This module comes with a black anodized aluminum ring that fits over the base body • Dimensions: A1: .51” (13mm), A2: .35” (9mm), D1: .86” (22mm), D2: .78” (20mm) •Thread Stud: M8 x 012mm •Sold in pairs Note: The unit can be installed flat without the aluminum ring, leaving only the lens visible.This requires drilling a .79” (20 mm) wide hole.Alternatively, the unit can be mounted with the aluminum ring on e.g. a retaining plate on the vehicle. 0634-0589 0634-0592 2020-2057 2020-2059
RkJQdWJsaXNoZXIy NDI5NTY=