Alpinestars Apparel Collection 2025 ALPINESTARS.COM
2 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 SIZE XS S M L XL 2XL 3XL TECH 10 AIR 2701-1099 2701-1100 2701-1101 2701-1102 2701-1103 2701-1104 2701-1105 * COMPATIBLE WITH THE FOLLOWING SUITS: FUSION, MISSILE IGNITION V2, MISSILE V2, STELLA MISSILE V2, AND GP TECH V4 TECH-AIR® 10 AIRBAG SYSTEM PRICE: $ 1436.95
3 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 TECH-AIR® 10 AIRBAG SYSTEM Developed from years of research with the world’s top MotoGP riders, and Alpinestars’ customers, data from millions of kilometers and thousands of crashes have been analyzed to continuously improve the intelligent crash detection algorithm. Upon the detection of a crash situation, a protective airbag is deployed, providing unrivaled protection to the rider with a maximum inflation time of 40ms. The Tech-Air® 10 System is extremely easy to use; just zip up the front and close the belt to activate the Airbag System, and you’re ready to ride. The internal belt automatically activates the System once it is fastened and secured. In Race Mode, the Tech-Air® 10 System is active only while riding above approximately 60km/h (37mph) for at least 10 seconds. Before this activation or when the rider’s speed drops steadily below such speed for at least 10 seconds, the System deactivates. This is the standard behavior of the Tech-Air® 10 Airbag System when in Race Mode, as it is normal to have fast stop and go riding situations where the rider doesn’t want to switch off the airbag. In such conditions, it is safer for the rider to have the airbag automatically deactivated by the System to avoid undesired deployments of the airbag, above all considering that the risk to be hit from another vehicle is negligible in racing conditions. There is a dedicated area on the System’s internal belt which serves as the charging base for the remote wireless LED display. A fully charged LED Display operates for at least 20 hours. The remote wireless LED display can be moved onto the rider’s arm to easily check the System’s status. The LED display can also be attached to the bike, depending on the rider’s preference. The Tech-Air® 10 System, requires approximately 4 hours to recharge a discharged battery with the supplied USB Charger. A fully charged battery will provide approximately 24 hours of use. If limited time is available, charging the battery for approximately 1 hour will provide approximately 6 hours of use. The System comes equipped with a USB charger and a magnetic Type C USB Cable that allows for quick, easy and convenient recharging. The airbag itself is breathable, designed with air channels and a perforated back zone that provide airflow to improve rider comfort. The Tech-Air® 10 System may be quickly attached to the Alpinestars’ TechAir® 10 System Base Layer via easy-to-use lateral zips; this allows riders to substitute the base layer between riding sessions if desired. The Tech-Air® 10 System Base Layer is hand washable. The total weight of the Tech-Air® 10 (System and base layer) is 2.390 gr for a size medium. Tech-Air® 10 is designed for track and road use and can be used with both the RACE and the STREET Riding Modes which have specific AI crash detection algorithms. The RACE Riding mode must only be used for riding on closed racetracks and should not be used for any other types of riding. Bluetooth connectivity to a Tech-Air® App provides riders with the Airbag System’s operational status, battery status and MyRide trip information. Via the Tech-Air® App, riders can also update the System’s firmware when new crash-detection algorithms are released. The Tech-Air® 10 Airbag System provides an even greater level of comprehensive coverage due to the additional protection of the riders’ hips and requires 2 argon gas inflators to fill the entire volume of the larger airbag when it is deployed in a crash situation. As such, TechAir® 10 does not have the dual charge concept like that of the Tech-Air® Race System. The Tech-Air® 10 System features an airbag that is certified for up to three inflations. However, after each deployment, when the System is received for service, the authorized Alpinestars Tech-Air® Service Centre will perform an inflation test on the airbag to check if the airbag has been damaged during the deployment. If the inflation test is passed, confirming that the airbag was not damaged during the deployment, the service will involve only the replacement of the gas inflators. If the inflation test is not passed, it means that the airbag was damaged during the deployment, and the System will undergo the full service that will involve the replacement of the gas inflators and the airbag. At the third deployment, the System will mandatorily undergo a full service, with the gas inflators and airbag being replaced. For more information regarding the operation of the Tech-Air® 10 System, please see the Tech-Air® 10 Product System Manual at: https://www.alpinestars.com/pages/product-manuals Tech-Air® 10 is the latest innovative autonomous airbag to join the Alpinestars’ Tech-Air® family, which includes the Tech-Air® Race, Tech-Air® Street and TechAir® 5 electronic Airbag Systems. Derived from Alpinestars’ airbag technology adopted by MotoGP riders, Tech-Air® 10 is a slim, self-contained wearable Airbag System that provides unrivaled body protection to racers, track day riders and road riders by covering the rider’s shoulders, chest, full back and hips. Tech-Air® 10 can be worn under any Alpinestars Tech-Air® Ready or Tech-Air® Compatible leather suits, or any third-party leather suit with 4 cm of space around the circumference of the rider’s chest and 2 cm of room around the circumference of the rider’s hips. The additional space for the chest and hips is necessary to be able to accommodate the inflation of the airbag, in the event of a crash. Designed to protect a motorcycle rider’s shoulders, chest, full back and hips, Tech- Air® 10 provides the most comprehensive coverage of any airbag currently available. The state-of-the-art, wearable Tech-Air® 10 Airbag System comes with an active electronic System that features 12 sensors (3 triaxial accelerometers plus 1 triaxial gyroscope) and a crash detection algorithm that leverages AI to accurately monitor when to deploy the airbag in the event of a crash. The impact absorption while wearing the airbag results in a decrease of the impact force by up to 95% compared to a passive protector. When deployed, the Tech-Air® 10 Airbag System offers the same protection as that provided by 18 back protectors. The Tech-Air® 10 has CE certification Level 2 for both the chest and back. A remote wireless LED display indicates the airbag’s operational status.
4 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 2701-1391 2701-1392 2701-1393 2701-1394 2701-1395 2701-1396 BLACK XS S M L XL 2XL SZ TECH-AIR® 7X SYSTEM PRICE: $ 1299.95 SIZE: XS - 2XL DESCRIPTION Tech-Air® 7x System is equipped with two Riding Modes, RACE and STREET, which have specific AI crash detection algorithms that can be easily selected via the Tech-Air® App. Tech-Air® 7x System is engineered to be worn under any Alpinestars Tech-Air® Ready or Tech-Air® Compatible leather suits or jackets, or any third-party leather suit with 4 cm of space around the circumference of the rider’s chest. The additional space for the chest is necessary to be able to accommodate the inflation of the Airbag in the event of a deployment. In addition, the leather suit should not be too tight in the crotch area, to prevent discomfort in the event of deployment. Tech-Air® 7x System is designed to be quickly and easily attached to Tech-Air® Compatible race suits or jackets for increased practicality and enhanced comfort. Tech-Air® 7x System is equipped with a convertor kit, allowing it to also be worn as a standalone Airbag System for real-world versatility. The Tech-Air® 7x System features dual charge capability, which means that with two full gas inflators, the System provides two separate Airbag deployments. Only one gas inflator will deploy to inflate the entire Airbag System during a crash scenario. A quick-release cover opening allows for rapid gas inflator replacement by users, only available in countries where gas inflator replacement by individuals is permitted by local regulations. The Tech-Air® 7x System uses an integrated, certified lithium-ion battery, with a fully charged battery life of approximately 20 hours of active ride time, and a recharge time of approximately 4 hours; charging the battery for approximately 1 hour will provide approximately 7 to 8 hours of riding time. Ease of use; to turn on the Tech-Air® 7x System, simply close the Front Flap, taking care to correctly attach the hook and loop patches. An internal magnetic switch will detect the Front Flap is closed and the System will automatically turn on and activate the Airbag System. To deactivate the Airbag, open the Front Flap and it will automatically turn off. The Tech-Air® 7x System’s base layer can be handwashed separately, after the removal of the non-washable parts that include the Airbag, Gas Inflators, and ALL the electronic components, including the LED Display, and the wiring. 2701-14123 REPLACEMENT TECH AIR INFLATORS
5 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 2701-1423 TECH AIR 7X REPLACEMENT INFLATORS PRICE: $ 279.95 KEY FEATURES Tech-Air® 7x System is equipped with two Riding Modes, RACE and STREET, which have specific AI crash detection algorithms that can be easily selected via the Tech-Air® App. Tech-Air® 7x System is engineered to be worn under any Alpinestars Tech-Air® Ready or Tech-Air® Compatible leather suits or jackets, or any third-party leather suit with 4 cm of space around the circumference of the rider’s chest. The additional space for the chest is necessary to be able to accommodate the inflation of the Airbag in the event of a deployment. In addition, the leather suit should not be too tight in the crotch area, to prevent discomfort in the event of deployment. Tech-Air® 7x System is designed to be quickly and easily attached to Tech-Air® Compatible race suits or jackets for increased practicality and enhanced comfort. Tech-Air® 7x System is equipped with a convertor kit, allowing it to also be worn as a standalone Airbag System for real-world versatility. The Tech-Air® 7x System features dual charge capability, which means that with two full gas inflators, the System provides two separate Airbag deployments. Only one gas inflator will deploy to inflate the entire Airbag System during a crash scenario. A quick-release cover opening allows for rapid gas inflator replacement by users, only available in countries where gas inflator replacement by individuals is permitted by local regulations. The Tech-Air® 7x System uses an integrated, certified lithium-ion battery, with a fully charged battery life of approximately 20 hours of active ride time, and a recharge time of approximately 4 hours; charging the battery for approximately 1 hour will provide approximately 7 to 8 hours of riding time. Ease of use; to turn on the Tech-Air® 7x System, simply close the Front Flap, taking care to correctly attach the hook and loop patches. An internal magnetic switch will detect the Front Flap is closed and the System will automatically turn on and activate the Airbag System. To deactivate the Airbag, open the Front Flap and it will automatically turn off. The Tech-Air® 7x System’s base layer can be handwashed separately, after the removal of the non-washable parts that include the Airbag, Gas Inflators, and ALL the electronic components, including the LED Display, and the wiring. PROTECTION The Tech-Air® 7x System is compatible with all FIM Grand Prix Requirements for Airbag Systems, making it suitable for road racing competitions. The Tech-Air® 7x System features the latest evolution of Alpinestars Tech-Air® technology, including a more compact and complete active electronic System that is equipped with 12 sensors. There are 4 tri-axial sensors: 1 tri-axial accelerometer and 1 tri-axial gyroscope located on the main electronic control unit, and 2 additional tri-axial accelerometers located on the shoulders, specifically developed for track and performance riding, and these combine with the Tech-Air® algorithm to accurately monitor when to deploy the Airbag in the event of a crash. Upon the detection of a crash situation, a protective Airbag is deployed, providing unrivaled protection to the rider with a maximum inflation time of 44ms depending on the Airbag size. The Airbag has been fully certified for up to 4 Airbag deployments before having to replace it, providing the Airbag hasn’t been damaged in one of the first 3 deployments. This Airbag System is certified as a Category II PPE (Personal Protective Equipment) under European Regulation (EU) 2016/425. Certifications of the Airbag System covered by Dolomiticert’s guidelines for inflatable protectors with electronic activation: Airbag System Central Back inflatable protector, Level 2, EN 1621-4:2018 STREET and RACE Algorithms performance Additional Tech-Air® 7x System Certifications: Protective garment, Class C, EN 17092-6:2020 Integrated Passive Central Back, Level 1, EN 1621-2:2014 Tech-Air® 7x System is certified as an undergarment, to be used in combination with and under a protective garment. The integrated back protector is extended for protection of the coccyx. TECH AIR 7X REPLACEMENT INFLATORS
6 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 PRICE: $ 999.95 TECH-AIR® 5 PLASMA BLACK CODE SIZE 2701-1424 XS 2701-1425 S 2701-1426 M 2701-1427 L 2701-1428 XL 2701-1429 XXL 2701-1430 3XL 2701-1431 4XL DESCRIPTION Innovated to meet the demands of an increasingly safety-conscious market, the groundbreaking, and ultra-lightweight Tech-Air® 5 PLASMA Airbag System is engineered to fit seamlessly under a jacket, providing a supremely comfortable and adaptive fit. The System’s ultra-slim, lightweight profile delivers an “invisible under the jacket” feel, creating a sensation of freedom while delivering advanced protection for an exceptional user experience. Constructed from Alpinestars’ best-in-class protective technology, the Tech-Air® 5 PLASMA Airbag System is the newest addition to the Alpinestars Tech-Air® family. Engineered for an ultra-lightweight, superior comfort, and an ‘invisible’ profile, the state-of-the-art Tech-Air® 5 PLASMA provides comprehensive upper body coverage, chest, ribs, back, and shoulders, and is equipped with a PLASMA back protector for the optimum blend of comfort, flexibility, airflow, and protection. With a new dedicated algorithm with three modes, STREET, ADVENTURE, and RACE, the Tech-Air® 5 PLASMA is a single-charge deployment Airbag System, and its gas canister is replaceable by the user. KEY FEATURES Full Upper Body Coverage: The Tech-Air® Airbag System provides comprehensive upper-body protection for the chest, ribs, back, and shoulders while remaining exceptionally light. Ultra-Lightweight: Weighing just 1530g, it’s over 25% lighter than the Tech-Air® 5, making it the lightest Tech-Air® System to date. Ultra-Slim, Invisible Profile: With its ultra-slim, minimal material construction, the System remains discreet and invisible under a jacket, enhancing rider comfort and wearability without adding bulk. Superior Comfort and Breathability: The full-stretch construction is designed for superior breathability, with a moisture-wicking treatment for maximum rider comfort. PLASMA Technology Inside: Equipped with an integrated Nucleon PLASMA back protector. Unique to Alpinestars, PLASMA is an eco-friendly, sustainable, and lightweight impact-absorbing material, while its clever design delivers class-leading levels of adaptability, breathability, ventilation, and adaptivity for the optimum balance of force dispersion, flexibility, and comfort. Optimized Lightweight Design: The ultra-thin, mono-layer stretch mesh chassis is engineered to contour perfectly with the shape of the airbag, minimizing the System’s material bulk, making it ideal for riders looking for an ultra-lightweight Airbag System with superior breathability. Faster Inflation and Easy Maintenance: An all-new single-canister design reduces weight, enables faster inflation, and simplifies servicing for quick turnaround. User-Friendly, Quick-Release Cover: The quick-release cover is attached to the chassis with a Velcro hook-and-loop patch for ease of use. The cover design allows easy access for gas inflator replacement, simply insert a finger into the recess and lift the cover to detach it. 2701-1480 REPLACEMENT TECH AIR INFLATOR
ALPINESTARS APPAREL COLLECTION 2025 Quick-Release Cover Design for Rapid Gas Inflator Replacement: The quick-release cover is attached to the chassis with a Velcro hook-and-loop patch for ease of use. The cover design allows quick gas inflator replacement—simply insert a finger into the recess and lift to detach the cover and access the gas inflator. Autonomous replacement of the gas inflator is available in countries where gas inflator handling by individuals is permitted by local regulations. Modular Design: Modular design for ease of use. Long-Lasting Battery Life: provides up to 30 hours of riding time, ensuring reliability for long rides. Extended Sizing: Available in four sizes XS-S, M-L, XL-2XL, and 3XL-4XL to accommodate all body shapes. MODES AND LED The Tech-Air® 5 PLASMA Airbag System offers three possible Riding Modes: STREET, OFF-ROAD, and RACE. After the System has been correctly switched on, the User can easily switch between the three different Riding Modes by pressing the System Button for 2 seconds. A SOLID GREEN LED will appear on the Riding Mode LED indicating which Riding Mode is currently running. Cycle through the modes until the desired mode is selected. The Tech-Air® 5 PLASMA Airbag System’s LED button can be used to check the System’s status. Simply press the button; a vibration indicates the system is functioning correctly. CONSTRUCTION Ultra-thin mono-layer stretch mesh construction at the collar, underarms, and front of the body, for an enhanced adaptive performance fit and superior breathability. Ergonomic sleeves with a deeper cut around the armpits for enhanced mobility and comfort. Cut longer at the rear for enhanced coverage, with a contoured, low-cut neck for reduced material contact with skin. Specifically engineered to work with Alpinestars jacket ventilation systems for optimized airflow and breathability. The Airbag is anatomically optimized to increase its envelope of protection. The Airbag features strategically positioned cutaways to precisely follow the shape and contours of the body for superior impact protection of the back, chest, neck, ribs, and shoulders, while also reducing material volume. Minimum use of plastic components for a low weight to performance ratio, and maximum airflow and freedom of movement. 7
8 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025
9 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 Tech-Air® 5 is a slim, fully selfcontained wearable airbag vest and standalone system; no external sensors are required for the System to operate. Provides upper body airbag coverage on back, shoulders, chest, and ribs. Can be worn with any Alpinestars’ Tech-Air® Ready jacket, or any properly fitting textile or leather motorcycling jacket with 4 cm of space around the circumference of the rider’s upper body to accommodate the inflation of the airbag in the event of a deployment. (always visit an authorized dealer to ensure an optimum fit and always follow the recommended sizing guidelines). The Tech-Air® 5 system, when inflated, offers the same protection as that provided by 18 CE certified Level 1 back protectors. Main chassis constructed from a lightweight mesh fabric with extensive mesh throughout for optimum levels of comfort and high levels of breathability. Perforated zone on the back protector for enhanced airflow and improved breathability. Specially developed internal air channels on interior of the vest’s back for additional airflow performance. Magnetic zip closure for ease of use and a secure closure. LED display on front hem indicates the airbag’s operational status. Robust internal housing located in the built-in CE-certified Nucleon back protector accommodates the system’s ECU and gas canisters. Back protector features an ergonomic plate construction for structural strength and a fit to follow the natural contours of the back. Comes equipped with Bluetooth connectivity with the free Tech-Air® App to show system and battery status, and MyRide trip mapping information. Tech-Air®’s ECU is seal-protected within vest to ensure the all-weather performance and the vest and componentry are certified to function between -10°C and 50°C. (-14°F and 122°F) ECU has been homologated to ECE R10 04 which ensures the electromagnetic integrity and stability of the unit. Tech-Air® uses an integrated, certified lithium-ion battery, with a battery life of 30 hours and a recharge time of approximately 4 hours. Argon inflator cartridges are CE certified to ISO 14451 standard, meaning that they will only fire if commanded by the electronic unit. It also certifies that the cartridges can be safely handled, assembled, and transported. System’s software is easily and conveniently upgradable via the free Tech-Air® App, and an external service record will be managed by Service Centers via the Tech-Air® Data Portal. The Tech-Air® 5 System is considered Category 2 Personal Protective Equipment under EU Regulation 2016/425, using a version of EN1621-4:2013, which guarantees impact protection performance from 25 – 40 milliseconds, depending on the Airbag System size to over 5 seconds of full pressure inflation. For more detailed explanation and warnings, refer to the information to be found in the Tech-Air® 5 System Manual. 2701-1044 2701-1045 2701-1046 2701-1047 2701-1048 2701-1049 2701-1050 2701-1051 ASH GREY BLACK XS S M L XL 2XL 3XL 4XL SZ TECH-AIR® 5 AIRBAG SYSTEM PRICE: $ 949.95
10 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 PRICE: $ 939.95 TECH-AIR® 3 LEATHER SYSTEM BLACK CODE SIZE 2701-1360 XS 2701-1361 S 2701-1362 M 2701-1347 L 2701-1348 XL 2701-1349 XXL 2701-1350 3XL 2701-1351 4XL Alpinestars’ lightest autonomous Airbag System, Tech-Air® 3 is designed to be worn over or under the motorcycle jacket, as the effective and practical choice for touring riders, urban city commuters and light off-road adventure riders. Alpinestars’ crash detection triggering algorithm has been developed and refined with millions of kilometers of riding data and thousands of crashes, allowing the System to accurately assess when to deploy the airbag ahead of an impact or other dangerous situation like a lowside or highside crash. In the event that Tech-Air® 3 detects the start of a crash, the System will inflate the protective airbag in 50 milliseconds. In the event of a direct impact of the motorcycle with another vehicle or obstacle, the Tech-Air® 3 System, is effective for the “first impact*,” which means that the System inflates before hitting the vehicle or obstacle against which the motorcycle will have the direct impact. The “first impact” test was performed in accordance with Dolomiticert Protocol where the airbag was tested within a speed range of 25 to 63 km/h. For more information on the envelope of protection, see the Tech-Air® 3 User Manual. Featuring a water resistant main chassis and a waterproof ECU and electronics, the slim, self-contained system can also be worn under a motorcycle jacket, including an Alpinestars’ Tech-Air® Ready jacket, or any leather or textile jacket, providing that the jacket has sufficient space to accommodate the inflation of the airbag. Tech-Air® 3 will allow riders to enjoy the daily commute even more, knowing they’re protected. Tech-Air® 3 is a fully autonomous active Airbag System and does not require any external connections or sensors on the motorcycle for the System to operate. Tech-Air® 3 incorporates 6 integrated sensors (3 accelerometers (1 triaxial accelerometer), and 3 gyroscopes (1 triaxial gyroscope )) to provide the best crash monitoring performance in a variety of dynamic riding situations, and even when stopped. Tech-Air® 3 uses a crash detection algorithm that leverages AI to accurately monitor when to deploy the airbag in the event of a crash, allowing the airbag to provide active protection in street riding scenarios and a variety of riding conditions, even when stopped. The Tech-Air® 3 Airbag System activates automatically via the magnetic zip closure. The System’s packable design allows it to be easily stored in a backpack or under a bike’s seat when not in use. Also available in a Stella women’s version, complete with an ergonomically engineered women’s optimized fit. Tech-Air® 3 is designed with a diagonal zipper to provide complete front chest coverage while also concealing the inner airbag. The magnetic zip closure has been designed for ease of use and to provide a secure closure system to the airbag garment. An LED display on the front chest indicates the airbag’s operational status. The LED display also incorporates a haptic alert, which vibrates to confirm the System is armed, and alerts the rider when the battery is running low. Integrated back protector pocket on the back can house additional passive back protection. 2701-1481 REPLACEMENT TECH AIR INFLATOR
11 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 Tech-Air® 3 incorporates Alpinestars’ Pro 2nd Generation compact Electronic Control Unit (ECU) which may be found in the ECU pocket located in the upper back of the inner, Tech-Air® 3 vest. Bluetooth low energy (BLE 5.0) connectivity to the Tech-Air® App allows riders to monitor the System’s operational status, battery status, as well as provides a detailed map of motorcyclists rides via MyRide. Upgradable system software is accessible via the Tech-Air® App, where riders can quickly verify the installed software version and eventually perform the latest software updates. Tech-Air® 3 uses an integrated, certified lithium ion battery, with a battery life of 40 hours and a recharge time of approximately 4 hours. The gas inflator that provides the inflation gas for the airbag’s deployment is located in the inflator housing on the left side of the lower back of the rider. Tech-Air® 3’s ECU seal-protection ensures all-weather performance and is certified to function between -20 °C and +40°C. The gas inflator housing, electronic wiring, and the airbag are easily removable. The gas inflator canisters can be replaced by select Alpinestars dealers and certified Tech-Air Service Centers. The vest is washable. The ECU has been tested and CE Certified according to different regulations for electronic, radio devices and electrical safety. The gas inflator cartridge is CE certified to UNI EN 16263, confirming compliance with the safety standard and certifying that the cartridges can be safely handled and serviced. According to European statutory law the CE mark is a conformity requirement for the marketing of this product. The following standards apply to this product: When inflated, the Tech-Air® 3 full chest and full back protection from the airbag is Category II CE Certified to the (EU) 2016/425 EEC European Personal Protective Equipment (PPE) Regulation, according to relevant part of EN1621-4:2013 airbag certification standard, which guarantees an impact protection performance of not less than five seconds after the activation. The impact attenuation performance is Level 2 both for full chest and full back. Impact protective garment 17092-6 Class C (outer garment), with the outershell constructed from water resistant material. *Note: 1. Performance tested according to DOLOMITICERT S.c.a.r.l. M.115.001 Protocol for Airbag Protectors Rev.4_14 10 2018. 2. For more detailed explanation and warnings, refer to the information to be found in the Tech-Air® 3 System Manual.
12 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 PRICE: $ 829.95 TECH-AIR® 3 CANVAS SYSTEM BLACK CODE SIZE 2701-1352 XS 2701-1353 S 2701-1354 M 2701-1355 L 2701-1356 XL 2701-1357 XXL 2701-1358 3XL 2701-1359 4XL Alpinestars’ lightest autonomous Airbag System, Tech-Air® 3 is designed to be worn over or under the motorcycle jacket, as the effective and practical choice for touring riders, urban city commuters and light off-road adventure riders. Alpinestars’ crash detection triggering algorithm has been developed and refined with millions of kilometers of riding data and thousands of crashes, allowing the System to accurately assess when to deploy the airbag ahead of an impact or other dangerous situation like a lowside or highside crash. In the event that Tech-Air® 3 detects the start of a crash, the System will inflate the protective airbag in 50 milliseconds. In the event of a direct impact of the motorcycle with another vehicle or obstacle, the Tech-Air® 3 System, is effective for the “first impact*,” which means that the System inflates before hitting the vehicle or obstacle against which the motorcycle will have the direct impact. The “first impact” test was performed in accordance with Dolomiticert Protocol where the airbag was tested within a speed range of 25 to 63 km/h. For more information on the envelope of protection, see the Tech-Air® 3 User Manual. Featuring a water resistant main chassis and a waterproof ECU and electronics, the slim, self-contained system can also be worn under a motorcycle jacket, including an Alpinestars’ Tech-Air® Ready jacket, or any leather or textile jacket, providing that the jacket has sufficient space to accommodate the inflation of the airbag. Tech-Air® 3 will allow riders to enjoy the daily commute even more, knowing they’re protected. Tech-Air® 3 is a fully autonomous active Airbag System and does not require any external connections or sensors on the motorcycle for the System to operate. Tech-Air® 3 incorporates 6 integrated sensors (3 accelerometers (1 triaxial accelerometer), and 3 gyroscopes (1 triaxial gyroscope )) to provide the best crash monitoring performance in a variety of dynamic riding situations, and even when stopped. Tech-Air® 3 uses a crash detection algorithm that leverages AI to accurately monitor when to deploy the airbag in the event of a crash, allowing the airbag to provide active protection in street riding scenarios and a variety of riding conditions, even when stopped. The Tech-Air® 3 Airbag System activates automatically via the magnetic zip closure. The System’s packable design allows it to be easily stored in a backpack or under a bike’s seat when not in use. Also available in a Stella women’s version, complete with an ergonomically engineered women’s optimized fit. 2701-1481 REPLACEMENT TECH AIR INFLATOR
13 APPAREL ALPINESTARS APPAREL COLLECTION 2025 Tech-Air® 3 is designed with a diagonal zipper to provide complete front chest coverage while also concealing the inner airbag. The magnetic zip closure has been designed for ease of use and to provide a secure closure system to the airbag garment. An LED display on the front chest indicates the airbag’s operational status. The LED display also incorporates a haptic alert, which vibrates to confirm the System is armed, and alerts the rider when the battery is running low. Integrated back protector pocket on the back can house additional passive back protection. Tech-Air® 3 incorporates Alpinestars’ Pro 2nd Generation compact Electronic Control Unit (ECU) which may be found in the ECU pocket located in the upper back of the inner, Tech-Air® 3 vest. Bluetooth low energy (BLE 5.0) connectivity to the Tech-Air® App allows riders to monitor the System’s operational status, battery status, as well as provides a detailed map of motorcyclists rides via MyRide. Upgradable system software is accessible via the Tech-Air® App, where riders can quickly verify the installed software version and eventually perform the latest software updates. Tech-Air® 3 uses an integrated, certified lithium ion battery, with a battery life of 40 hours and a recharge time of approximately 4 hours. The gas inflator that provides the inflation gas for the airbag’s deployment is located in the inflator housing on the left side of the lower back of the rider. Tech-Air® 3’s ECU seal-protection ensures all-weather performance and is certified to function between -20°C and +40°C. The gas inflator housing, electronic wiring, and the airbag are easily removable. The gas inflator canisters can be replaced by select Alpinestars dealers and certified Tech-Air Service Centers. The vest is washable. The ECU has been tested and CE Certified according to different regulations for electronic, radio devices and electrical safety. The gas inflator cartridge is CE certified to UNI EN 16263, confirming compliance with the safety standard and certifying that the cartridges can be safely handled and serviced. According to European statutory law the CE mark is a conformity requirement for the marketing of this product. The following standards apply to this product: When inflated, the Tech-Air® 3 full chest and full back protection from the airbag is Category II CE Certified to the (EU) 2016/425 EEC European Personal Protective Equipment (PPE) Regulation, according to relevant part of EN1621-4:2013 airbag certification standard, which guarantees an impact protection performance of not less than five seconds after the activation. The impact attenuation performance is Level 2 both for full chest and full back. Impact protective garment 17092-6 Class C (outer garment), with the outershell constructed from water resistant material. *Note: 1. Performance tested according to DOLOMITICERT S.c.a.r.l. M.115.001 Protocol for Airbag Protectors Rev.4_14 10 2018. 2. For more detailed explanation and warnings, refer to the information to be found in the Tech-Air® 3 System Manual.
14 APPAREL ALPINESTARS APPAREL COLLECTION 2025 PRICE: $ 749.95 TECH-AIR 3 SYSTEM BLACK CODE SIZE 2701-1176 XS 2701-1177 S 2701-1178 M 2701-1179 L 2701-1180 XL 2701-1181 XXL 2701-1182 3XL 2701-1183 4XL Alpinestars’ lightest autonomous Airbag System, Tech-Air® 3 is designed to be worn over or under the motorcycle jacket, as the effective and practical choice for touring riders, urban city commuters and light off-road adventure riders. Alpinestars’ crash detection triggering algorithm has been developed and refined with millions of kilometers of riding data and thousands of crashes, allowing the System to accurately assess when to deploy the airbag ahead of an impact or other dangerous situation like a lowside or highside crash. In the event that Tech-Air® 3 detects the start of a crash, the System will inflate the protective airbag in 50 milliseconds. In the event of a direct impact of the motorcycle with another vehicle or obstacle, the TechAir® 3 System, is effective for the “first impact*,” which means that the System inflates before hitting the vehicle or obstacle against which the motorcycle will have the direct impact. The “first impact” test was performed in accordance with Dolomiticert Protocol where the airbag was tested within a speed range of 25 to 63 km/h. For more information on the envelope of protection, see the Tech-Air® 3 User Manual. Featuring a water resistant main chassis and a waterproof ECU and electronics, the slim, self-contained system can also be worn under a motorcycle jacket, including an Alpinestars’ Tech-Air® Ready jacket, or any leather or textile jacket, providing that the jacket has sufficient space to accommodate the inflation of the airbag. Tech-Air® 3 will allow riders to enjoy the daily commute even more, knowing they’re protected. Tech-Air® 3 is a fully autonomous active Airbag System and does not require any external connections or sensors on the motorcycle for the System to operate. Tech-Air® 3 incorporates 6 integrated sensors (3 accelerometers (1 triaxial accelerometer), and 3 gyroscopes (1 triaxial gyroscope )) to provide the best crash monitoring performance in a variety of dynamic riding situations, and even when stopped. Tech-Air® 3 uses a crash detection algorithm that leverages AI to accurately monitor when to deploy the airbag in the event of a crash, allowing the airbag to provide active protection in street riding scenarios and a variety of riding conditions, even when stopped. The Tech-Air® 3 Airbag System activates automatically via the magnetic zip closure. The System’s packable design allows it to be easily stored in a backpack or under a bike’s seat when not in use. Also available in a Stella women’s version, complete with an ergonomically engineered women’s optimized fit. Tech-Air® 3 is designed with a diagonal zipper to provide complete front chest coverage while also concealing the inner airbag. The magnetic zip closure has been designed for ease of use and to provide a secure closure system to the airbag garment. An LED display on the front chest indicates the airbag’s operational status. The LED display also incorporates a haptic alert, which vibrates to confirm the System is armed, and alerts the rider when the battery is running low. Integrated back protector pocket on the back can house additional passive back protection. Tech-Air® 3 incorporates Alpinestars’ Pro 2nd Generation compact Electronic Control Unit (ECU) which may be found in the ECU pocket
15 APPAREL ALPINESTARS APPAREL COLLECTION 2025 located in the upper back of the inner, Tech-Air® 3 vest. Bluetooth low energy (BLE 5.0) connectivity to the Tech-Air® App allows riders to monitor the System’s operational status, battery status, as well as provides a detailed map of motorcyclists rides via MyRide. Upgradable system software is accessible via the Tech-Air® App, where riders can quickly verify the installed software version and eventually perform the latest software updates. Tech-Air® 3 uses an integrated, certified lithium ion battery, with a battery life of 40 hours and a recharge time of approximately 4 hours. The gas inflator that provides the inflation gas for the airbag’s deployment is located in the inflator housing on the left side of the lower back of the rider. Tech-Air® 3’s ECU seal-protection ensures all-weather performance and is certified to function between -20 ⁰C and +40⁰C. The gas inflator housing, electronic wiring, and the airbag are easily removable. The gas inflator canisters can be replaced by select Alpinestars dealers and certified Tech-Air Service Centers. The vest is washable. The ECU has been tested and CE Certified according to different regulations for electronic, radio devices and electrical safety. The gas inflator cartridge is CE certified to UNI EN 16263, confirming compliance with the safety standard and certifying that the cartridges can be safely handled and serviced. According to European statutory law the CE mark is a conformity requirement for the marketing of this product. The following standards apply to this product: When inflated, the Tech-Air® 3 full chest and full back protection from the airbag is Category II CE Certified to the (EU) 2016/425 EEC European Personal Protective Equipment (PPE) Regulation, according to relevant part of EN1621-4:2013 airbag certification standard, which guarantees an impact protection performance of not less than five seconds after the activation. The impact attenuation performance is Level 2 both for full chest and full back. Impact protective garment 17092-6 Class C (outer garment), with the outershell constructed from water resistant material. *Note: 1. Performance tested according to DOLOMITICERT S.c.a.r.l. M.115.001 Protocol for Airbag Protectors Rev.4_14 10 2018. 2. For more detailed explanation and warnings, refer to the information to be found in the Tech-Air® 3 System Manual.
16 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 PRICE: $ 749.95 STELLA TECH-AIR 3 SYSTEM BLACK CODE SIZE 2701-1195 XS 2701-1196 S 2701-1197 M 2701-1198 L 2701-1199 XL 2701-1200 XXL Alpinestars’ lightest autonomous Airbag System, Stella Tech-Air® 3 is designed to be worn over or under the motorcycle jacket, as the effective and practical choice for touring riders, urban city commuters and light off-road adventure riders. The Stella Tech-Air® 3 is equipped with an ergonomically optimized women’s tailored female fit with a tapered cut for enhanced comfort. Alpinestars’ crash detection triggering algorithm has been developed and refined with millions of kilometers of riding data and thousands of crashes, allowing the System to accurately assess when to deploy the airbag ahead of an impact or other dangerous situation like a lowside or highside crash. In the event that Stella Tech-Air® 3 detects the start of a crash, the System will inflate the protective airbag in 50 milliseconds. In the event of a direct impact of the motorcycle with another vehicle or obstacle, the Tech-Air® 3 System, is effective for the “first impact*,” which means that the System inflates before hitting the vehicle or obstacle against which the motorcycle will have the direct impact. The “first impact” test was performed in accordance with Dolomiticert Protocol where the airbag was tested within a speed range of 25 to 63 km/hr. For more information on the envelope of protection, see the Tech-Air® 3 User Manual. Featuring a water resistant main chassis and a waterproof ECU and electronics, the slim, self-contained system can also be worn under a motorcycle jacket, including an Alpinestars’ Tech-Air® Ready jacket, or any leather or textile jacket, providing that the jacket has sufficient space to accommodate the inflation of the airbag. The Stella Tech-Air® 3 will allow riders to enjoy the daily commute even more, knowing they’re protected. The Stella Tech-Air® 3 is a fully autonomous active Airbag System and does not require any external connections or sensors on the motorcycle for the System to operate. The Stella Tech-Air® 3 incorporates 6 integrated sensors (3 accelerometers (1 triaxial accelerometer), and 3 gyroscopes (1 triaxial gyroscope )) to provide the best crash monitoring performance in a variety of dynamic riding situations, and even when stopped. The Stella Tech-Air® 3 uses a crash detection algorithm that leverages AI to accurately monitor when to deploy the airbag in the event of a crash, allowing the airbag to provide active protection in street riding scenarios and a variety of riding conditions, even when stopped. The Stella Tech-Air® 3 Airbag System activates automatically via the magnetic zip closure. The System’s packable design allows it to be easily stored in a backpack or under a bike’s seat when not in use. The Stella Tech-Air® 3 is designed with a diagonal zipper to provide complete front chest coverage while also concealing the inner airbag. The magnetic zip closure has been designed for ease of use and to provide a secure closure system to the airbag garment. An LED display on the front chest indicates the airbag’s operational status. The LED display also incorporates a haptic alert, which vibrates to confirm the System is armed, and alerts the rider when the battery is running low. Integrated back protector pocket on the back can house additional passive back protection.
17 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 The Stella Tech-Air® 3 incorporates Alpinestars’ Pro 2nd Generation compact Electronic Control Unit (ECU) which may be found in the ECU pocket located in the upper back of the inner, Tech-Air® 3 vest. Bluetooth low energy (BLE 5.0) connectivity to the Tech-Air® App allows riders to monitor the System’s operational status, battery status, as well as provides a detailed map of motorcyclists rides via MyRide. Upgradable system software is accessible via the Tech-Air® App, where riders can quickly verify the installed software version and eventually perform the latest software updates. The Stella Tech-Air® 3 uses an integrated, certified lithium ion battery, with a battery life of 40 hours and a recharge time of approximately 4 hours. The gas inflator that provides the inflation gas for the airbag’s deployment is located in the inflator housing on the left side of the lower back of the rider. The Stella Tech-Air® 3’s ECU seal-protection ensures all-weather performance and is certified to function between -20 °C and +40°C. The gas inflator housing, electronic wiring, and the airbag are easily removable. The gas inflator canisters can be replaced by select Alpinestars dealers and certified Tech-Air Service Centers. The vest is washable. The ECU has been tested and CE Certified according to different regulations for electronic, radio devices and electrical safety. The gas inflator cartridge is CE certified to UNI EN 16263, confirming compliance with the safety standard and certifying that the cartridges can be safely handled and serviced. According to European statutory law the CE mark is a conformity requirement for the marketing of this product. The following standards apply to this product: When inflated, the Stella Tech-Air® 3 full chest and full back protection from the airbag is Category II CE Certified to the (EU) 2016/425 EEC European Personal Protective Equipment (PPE) Regulation, according to relevant part of EN1621-4:2013 airbag certification standard, which guarantees an impact protection performance of not less than five seconds after the activation. The impact attenuation performance is Level 2 both for full chest and full back. Impact protective garment 17092-6 Class C (outer garment), with the outershell constructed from water resistant material. *Note: 1. Performance tested according to DOLOMITICERT S.c.a.r.l. M.115.001 Protocol for Airbag Protectors Rev.4_14 10 2018. 2. For more detailed explanation and warnings, refer to the information to be found in the Tech-Air® 3 System Manual.
18 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025 2701-1290 2701-1291 2701-1292 2701-1293 2701-1294 2701-1423 BLACK S M L XL 2XL SZ TECH-AIR® OFFROAD AIRBAG SYSTEM Tech-Air® Off-Road is an FIM homologated airbag system designed specifically to handle the rigors of Rally riding while offering unrivalled upper body protection. Developed and tested in the most grueling conditions such as the Dakar, the TechAir® Off-Road System combines Alpinestars’ Bionic Pro Protection Jacket with Tech-Air® technology and a Rally-dedicated crash detection algorithm to deliver proven, off-road specific protection to the back, chest, shoulders, collarbones and neck. Although tough enough to tackle the world’s toughest rallies, this system has three riding modes, RALLY, ENDURO and STREET, making it the perfect choice for tackling every type of off-road riding, whatever the terrain. 1. Proven to be more than twice as protective as passive impact protectors. 2. Dual inflators deliver two deployments for guaranteed protection 3. Average inflation time of just 50 milliseconds (40ms for the smaller sizes and up to a max of 60ms for the largest 2XL). 4. Increased airbag coverage on back, shoulders, chest and ribs for complete upper body protection. 5. Neck protection is provided by the airbag inflating around the neck. 6. The integrated Nucleon CELL Back Protector is light, flexible and highly ventilated for enhanced performance, and features an ergonomic plate construction for structural strength and a fit to follow the natural contours of the back. 7. The Tech-Air® Off-Road System is Category II CE Certified to the 686/89/ EEC European PPE Directive, using a version of EN1621- 4:2013, which guarantees impact protection performance from within 25 milliseconds to 5 seconds of full pressure inflation. 8. Neck protectors are NOT compatible with the TechAir® Off-Road System. Premium materials combined with innovative design create a protector that is light, ergonomic and robust. Constructed from a breathable stretch mesh for superior ventilation while keeping the protection close to the rider’s body. Slim fit stretchable fabric construction features a floating, highly ventilated and flexible thermoformed chest protector for an optimal riding experience. CE Certified passive protectors for additional protection against impacts in key areas. Central front zipper for a better fit and ease of use. Additional front padding on the arms and chest for enhanced roost protection. Height adjustable kidney belt for an optimal fit. Ergonomic design delivers exceptional rider comfort and freedom of movement. Water bladder compatible: back holder for Hydration pack already included. PRICE: $ 1249.95 SIZE: S - 2XL REPLACEMENT TECH AIR 2X INFLATORS 2701-1423 TECH AIR 7X REPLACEMENT INFLATORS PRICE: $ 279.95 TECH AIR OFFROAD REPLACEMENT INFLATORS
19 TECH-AIR® ALPINESTARS APPAREL COLLECTION 2025
20
The Supertech R10 draws on Alpinestars depth of experience from 60 years of world-class innovation across all fields of motorsport. A result of more than 10 years of intensive study, development, and testing, Alpinestars first full face road racing helmet features ultra-lightweight materials, a supremely aerodynamic profile with inter-changeable rear spoilers, an extensive ventilation system and unsurpassed levels comfort, in a package that delivers the highest protection to all track and road riders. 21
SUPERTECH R10 HELMET Alpinestars brings the Supertech R10 road racing helmet following years of extensive research, development, and testing by Alpinestars’ Helmet Product Development Department, together with MotoGP legend Andrea Dovizioso, and MotoGP riders’ Jorge Martin, and Jack Miller. With the S-R10, the focus of the design was to ensure the highest level of performance, especially when it comes to protection and a new level of safety. The S-R10 Helmet has been engineered to provide the perfect blend of excellent ventilation, unsurpassed comfort, and the lightest weight possible, without compromising on any other front. Another crucial element unique to the S-R10’s design and development is the helmet’s advanced aerodynamics, with countless sessions in the wind tunnel aimed at reducing drag and providing optimal aerodynamic stability. OUTER SHELL Carbon shell construction mult-layer composite disperses energy in impacts +Homologated to ECE 22.06, DOT, and FIM standards, the Supertech R10’s shell construction utilizes a highly advanced molding technology with a multicomposite combination featuring a 3K high-density carbon outer later, a unidirectional carbon composite layer, an aramid fiber layer, and a fiberglass one. The 3K high density carbon outer layer provides excellent strength and efficiency of energy dissipation over the shell. The uni-directional (UD) carbon composite layer provides significantly greater radial strength around the shell, preventing compression, but allowing controlled deflection for reducing transmitted impact energy. And the aramid fiber plus fiberglass layers provide critical penetration protection. This layered composite combination created by bonding everything together with an advanced epoxy resin already applied on the pre-preg fiber, perfectly controls the ideal proportion of resin versus fiber to maximize strength, mechanical performance, and lightweight. The combination of material layers provides improved energy management, as well as limited outer shell deflection, making the energy spread wider and better absorbed by the EPS liner. The S-R10’s unique shell construction results in extremely effective impact protection. With a fully equipped in-house helmet testing facility within Alpinestars’ state-of-the-art Research and Development center, the company has carried out an exhaustive impact research program. Our research and development efforts have shown the S-R10 returning linear and oblique impact performance results which far exceed current ECE 22.06 helmet regulation standard limits. For direct linear impacts, which is an impact at a 90-degree angle between the helmet and an object, the S-R10 surpasses the standard by an average magnitude of 37%. And for rotational acceleration and oblique impact performance, where impact energy comes from an angle other than a linear 90-degree, or right-angle straight impact, the S-R10 exceeds the standard by 65%. INNER SHELL The S-R10’s inner shell is made from eps in different densities. The S-R10 has four inner shells just like the outer shell and is available in four anatomical sizes. The S-R10’s construction is optimized to ensure riders have the correct fit, which not only improves comfort and reduces overall weight, but most importantly, improves the effectiveness of the helmet in an impact. Underneath the helmet’s outer shell is an eight-piece multi-density EPS liner, with six specific densities that are strategically positioned in different zones to ensure excellent energy absorption from impact forces dissipated over the outer shell, as well as a close and comfortable fit. The EPS liner, just like the outer shell, has its own unique dimension for each helmet size, further tailoring the helmet’s performance and fit when it comes to protection and comfort. Linear and oblique force management The EPS inner surface is smooth, creating an optimized, low friction area, for superior oblique impact management. When it comes to other types of helmet testing, the best helmets are those that provide protection against rotational, as well as oblique and linear impact forces. 22
RkJQdWJsaXNoZXIy NDI5NTY=