WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2025. SECTION 7 534 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 0923-0381 For 07-16 Twin Cam (tapered wrist pin, 7.659” L) HEAVY-DUTY CONNECTING ROD SET •High-quality, heavy-duty rod set comes complete and ready-to-install •Set includes front and rear rods, crankpin and nuts, steel cages and roller bearings •Rods are deep-forged and heat-treated, 0.120” wider than stock in the I-beam section and feature rod-to-rod clearance to accommodate strokes up to and including 5” •Crankpin has two oil holes and rod has four slots ground on each side of the throw ends to help maintain the oil film on thrust faces •Made in the U.S.A. NOTE: Installation of rod sets may require additional clearancing of flywheels and cases. PART # DESCRIPTION 0921-0752 For 99-17 Big Twin and S&S “T” series engines 0921-0164 For 86-99 XL CRANKPIN ASSEMBLIES •For use in stock and S&S flywheels •Made in the U.S.A. PART # DESCRIPTION 0924-0391 For 99-17 Twin Cam (right side) INNER MAIN BEARING RACE •Sold each •Made in the U.S.A. PART # DESCRIPTION 0923-0354 For 05-17 Twin Cam (std.) WRIST PIN BUSHING •Constructed of SAE660 bearing bronze •Made to exact tolerances and will meet or exceed fitment and wearability of all other OE-style replacement bushings available •Sold each •Dimensions: 1.019” OD x 0.925” ID; overall length 1.040” •Made in the U.S.A. NOTE: Does not include oil holes. These must be drilled after installation. PART # DESCRIPTION 3801-0305 For 99-16 Twin Cam 0923-0379 For 99-16 Twin Cam w/ 5-piece flywheel, 99 Big Twin w/ V111, V117, V124 crank WRIST PIN BUSHINGS •Meet or exceeds fitment and wearability of OEM bushings •Sold each •Made in the U.S.A. PART # DESCRIPTION STANDARD 0921-0787 For 17-24 M-Eight engines 0921-0786 For 99-17 Twin Cam A engines 0921-0787 For 00-17 Twin Cam B engines PART # DESCRIPTION UNDERSIZED 0921-0938 For 17-24 M-Eight engines 0921-0938 For 00-17 Twin Cam B engines CRANKSHAFT BEARING RACE KITS •Include right and left side crankshaft races with the left side thrust washers •Press-on races have a precision-ground outer diameter finish and are designed to be true to size, producing the correct OD after proper press on installation •Pinion race on PART #0921-0938 is undersized to allow service and re-machining of pinion shaft when prior damage occurred such as race spinning on shaft •Made in the U.S.A. 0921-0787 0923-0379 0921-0164 PART # DESCRIPTION 0924-0108 For 99-02 Big Twin (set); repl. OEM #9028 0924-0270 For 86-03 XL; (set); repl. OEM #24729-74 CRANKCASE MAIN BEARINGS •High-quality original Timken® bearing assemblies •Made in the U.S.A. 0924-0108 0924-0270 PART # DESCRIPTION 0920-0143 For 99-17 Twin Cam w/ 3-piece flywheel with S&S V96, V107 and V113 flywheels LEFT INNER MAIN BEARING RACE •Quality replacement component •1.25” x 1.65” x 0.713”, hardened steel PART # DESCRIPTION DS-194074 For 99-06 Big Twin; repl. OEM #24003-55 MOTOR SPROCKET NUT •Motor sprocket nut for belt-drive conversions and/or eliminating compensating sprockets •Sold each •Made in the U.S.A.
RkJQdWJsaXNoZXIy NDI5NTY=