WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 7 All part numbers in BLUE are new for 2025. 563 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 0926-2973 For 17-24 M-Eight ENDURANCE BEEHIVE® VALVE SPRINGS WITH TITANIUM RETAINERS •Feuling® BeeHive® Endurance springs are direct bolt-in replacements, no machining or rocker box clearancing required •M-Eight: up to 0.565” cam lift •Machined from premium-grade hi-tensile chrome silicon single-conical ovate wire •Shot-peened with specially processed thermal heat treat and super NexTex® finish for fatigue life needed to exceed high demands of V-Twin engines •Use a much smaller and lighter weight retainer to reduce valve weight and create quicker rev and smoother motion •Standard, 6 mm valve stem (uses factory retainers) •Kit includes: Endurance BeeHive valve springs, optional lightweight Titanium retainers, machined spring seats, seat shims, valve locks and a set of premium Viton® valve seals equipped with spring-loaded valve stem wiper system •M-Eight specs: seat lbs./ installed height; 134 lbs. at 1.375” (0.405” lift), 127 lbs. at 1.405” (0.435” lift), 125 lbs. at 1.415” (0.445” lift), 121 lbs. at 1.435” (0.465” lift), 116 lbs. at 1.455” (0.485” lift), 113 lbs. at 1.470” (0.500” lift),109 lbs. at 1.490” (0.520” lift), 103 lbs. at 1.520” (0.550” lift), 226 lbs. at 0.970” (open height), coil bind at 0.920” •Feuling BeeHive valve springs must be installed at the correct OPEN HEIGHT, matching max lift to the open height spec of the valve springs •Made in the U.S.A. PART # DESCRIPTION 0926-3138 For 17-24 M-Eight w/ factory style 6 mm valve stems and triple groove HIGH-LOAD BEEHIVE® VALVE SPRINGS WITH TITANIUM RETAINERS FOR M-EIGHT •M-Eight High-Load springs are machined from a premium-grade hi-tensile chrome silicon single conical ovate wire, shot-peened with a specially processed thermal heat treat and super NexTex® finish to give these valve springs the needed fatigue life to exceed the high demands of V-Twin engines from stock to performance •Valve springs are recommended for 0.530”+ lift camshafts •Direct bolt-in replacement, no spring seat or rocker cover machining required up to 0.592” lift •Springs will accommodate over 0.600” cam lift, but will require spring seat pocket machining on the cylinder heads to set correct spring open height •Smaller lighter weight retainers which drastically reduce the valve weight creating a quicker revving and smoother motion than comparable dual or single valve springs •Eliminate valve spring separation, maximize stability, reduce valve-train noise and harmonics •Packaged as a matched set and must be installed at the correct OPEN HEIGHT •Matching max cam lift to the open height spec of the valve springs is essential for optimal valve-train operation and spring life (see included spring spec chart) •Kit includes: matched set of Feuling® High-Load BeeHive® valve springs, Titanium retainers, machined spring seats, seat shims, valve locks and a set of premium Viton® valve seals equipped with a spring-loaded valve stem wiper system •M-Eight specs: seat lbs./ installed height; 151 lbs. at 1.475” (0.485” lift), 144 lbs. at 1.498” (0.508” lift), 143 lbs. at 1.501” (0.511” lift), 140 lbs. at 1.511” (0.521” lift), 124 lbs. at 1.562” (0.578” lift), 120 lbs. at 1.582” (0.592” lift), 304 lbs. at 0.990” open height, coil bind at 0.945” (cam specs measured on the lifter at 0.050” lift with 1.61 rocker arm ratio) •Made in the U.S.A. NOTE: These springs are ONLY recommended for large lift camshafts over 0.530” lift such as the Reaper® 592 Cam PART #0925-1265 and RACE style engines as these valve springs have increased load and if used on smaller cams will create extreme rocker arm deflection. NOTE: Valve seat cutter and pilot may be needed to achieve correct valve spring installed height on large lift camshafts (PART #s 3801-0364 and 3801-0365).
RkJQdWJsaXNoZXIy NDI5NTY=