WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES All part numbers in BLUE are new for 2025. SECTION 7 610 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. HIGH FLOW CAMPLATES FOR TWIN CAM •Increase engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages •Camplate matches the oil portholes throughout the camplate to the port holes in the engine case increasing engine oil flow throughout the engine •25 to 35 degree cooler engine temperatures and 20 to 30 degree cooler oil temperatures •Made from 7075 billet aluminum which is 50% harder and stronger than the factory, SE® and other aftermarket camplates •The 7075 increases the strength and hardness of the camplate, holding tighter tolerances under temperature eliminating flexing and the need for bronze bushings •Camplates are pressure tested and pressure relief valve is seated, sealed and set to pop off at 55 to 60 psi •When matched with the Feuling® Race Series® oil pump rear wheel power gains of 3 hp and 4 ft/lbs of Torque can be achieved •For use ONLY with the Feuling oil pumps •Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerances for improved press fit PART # DESCRIPTION EMIS* FOR 07-17 TWIN CAM AND 06 DYNA 0925-01101, 2 For chain or gear drive cams 4 PART # DESCRIPTION EMIS* FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0920-00063 For gear drive cams 3 CAMPLATE FOR M-EIGHT •Precision-machined from billet aluminum •Blue anodized finish •Passage plugs are removable for servicing •For use with OEM or S&S oil pumps •Made in the U.S.A. CAMPLATE FOR TWIN CAM •Precision CNC-machined forged aluminum •Adjustable oil pressure regulator; adjust without removing plate from the engine •Passage plugs are removable for service •Rebuildable bronze pinion shaft bushing in all models and bronze cam bushings in 07-later style •Made in the U.S.A. NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. BLOCK-OFF PLATE KIT •Block-off hydraulic chain tensioner holes when using gear-driven cams •Made in the U.S.A. PART # DESCRIPTION 0932-0268 For 17-23 M-Eight PART # DESCRIPTION 0925-0914 For 07-17 Twin Cam and 06 Dyna PART # DESCRIPTION 0925-0915 For 99-06 Twin Cam (except 06 Dyna) PART # DESCRIPTION 0932-0036 For 17-24 M-Eight, 07-17 Twin Cam and 06 Dyna camplates 0925-0914 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 Requires the use of 07-17 style Feuling® HP+® or Race Series® oil pump PART #s 0932-0023 or 0932-0026. 3 Requires the use of 99-06 style Feuling HP+ or Race Series oil pump PART #s 0932-0018 or 0932-0020. •Bearing and retainer plate hardware is included •Camplates for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal tolerance for improved cam fitment •Added cam journal oil groove for cold startup protection and increased cam journal lubrication •Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear •Made in the U.S.A. 0925-0006 0925-0110
RkJQdWJsaXNoZXIy NDI5NTY=