BOLD MAGENTA part numbers are new for 2025 PARTSCANADA.COM 2025 | SNOW RIDER & SLED ACCESSORIES 150 RAM® UNIVERSAL CAMERA AND CAMCORDER ADAPTERS • Consists of a 1” diameter rubber ball connected to a round base with 1/4”-20 camera thread •Round base provides extra support and stability for cameras that rest on top of it • PART #0603-0892 does not include a base, only a threaded steel stud •Male 1/4”-20 threaded steel stud will connect to any standard female thread found on camcorders and digital cameras • Compatible cameras include Contour GPS, Contour HD, Gobandit GPS-HD, GoPro® HD helmet HERO, GoPro HD Motorsports HERO, GoPro HD Surf HERO, GoPro Helmet HERO Wide, GoPro Motorsports HERO, GoPro Motorsports HERO Wide, GoPro RC HERO, GoPro Surf HERO and GoPro Wide HERO RAM® UNIVERSAL X-GRIP® CELL PHONE CRADLE WITH 1” BALL •High-strength composite and rustproof marine-grade stainless steel construction •Spring-loaded holder expands and contracts for perfect fit on your device •Rubber-coated tips will hold device firm and stable • Includes 1” ball; mount adapter is not required •Versatility of holder allows for attachment to many RAM® arms • Cradle dimensions: minimum width = 1.875” (minimum height = 4.25”) maximum width = 3.25” (minimum height = 2.25”) depth = 0.875” •It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size •X-Grip® includes a device tether FINGER-GRIP™ UNIVERSAL HOLDER WITH EZ-STRAP™ RAIL MOUNT •RAM® EZ-Strap™ base with double ball short arm, diamond adapter base and universal Finger-Grip™ cradle for cell phones and electronic devices • Strap can be cut to fit tubing, square rails and irregular shapes from 0.5” to 2.58” in diameter •Multiple adjustment points allow you to move the mount to your optimum viewing position •Mount rotates 180° •Cradle comes with three sets of four flexible rubber-coated fingers placed along sides to grip device •Fingers open by squeezing the ends of the holder •Bottom of the cradle includes a black plate that adds support to the device being held • Spine plate contains the universal AMPs and 1.5” x 2” hole patterns RAM® MOUNT ADAPTERS •Marine-grade aluminum with a black powdercoat finish • 1” rubber ball •Predrilled holes in bases allow mounting to a variety of arms and cradles RAM® UNIVERSAL FINGER-GRIP™ CRADLE •This mount is designed to hold cell phones (check measurements below for dimensions) and electronic devices •Made of up a high-strength composite •Comes with three sets of four flexible rubber-coated fingers placed along the sides to grip your device •The fingers open by squeezing the ends of the holder •The bottom of the holder includes a back plate that adds support to the device being held by the mount •Can also be used with several other phone accessories •The spine plate contains the universal AMPS and 1.5” x 2” hole patterns •Height dimensions: minimum with top and bottom plates is 5.25” and maximum with top and bottom plates is 6.0” DESCRIPTION PART # 1” dia. rubber ball w/ a round base and 1/4”-20 camera thread 0603-0473 1” dia. rubber ball w/ 1/4”-20 camera thread 0603-0892 DESCRIPTION PART # X-Grip® cradle 0603-0478 DESCRIPTION PART # X-Grip® replacement tether 0603-1093 DESCRIPTION PART # Finger-Grip™ w/ EZ-Strap™ rail mount 0603-1026 DESCRIPTION PART # Ball w/ adapter AMPS hole 0603-0471 Ball w/ diamond-shaped adapter 0603-0472 DESCRIPTION PART # RAM® universal Finger-Grip™ cradle 0603-0477 •The top and bottom plates can be removed for larger devices • Spine plate dimensions: 3”W x 3” H •Using short-arm side clamps: maximum depth is 0.75”, minimum width is 1.25” and maximum width is 3.0” •Using medium-arm side clamps: maximum depth is 1.25”, minimum width is 1.5” and maximum width is 3.5” •Using long-arm side clamps: maximum depth is 1.6”, minimum width is 2.25” and maximum width is 3.5” •Made in the U.S.A. NOTE: Does not come with ball mount adapter; use PART #0603-0472 to mount to RAM® double-socket arm. 0603-0471 0603-0472 0603-0473 0603-0478
RkJQdWJsaXNoZXIy NDI5NTY=