BOLD MAGENTA part numbers are new for 2025 PARTSCANADA.COM 2025 | STREET FUEL/AIR SYSTEMS FUEL/AIR SYSTEMS 1010 DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 4-6 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. DESCRIPTION PART # 1/8” ID – 3’ LENGTH Clear 0706-0138 3/16” ID X 5/16” OD – 3’ LENGTHS Black 0706-0044 Clear 0706-0041 Gray 0706-0038 DESCRIPTION PART # 1/4” ID X 7/16” OD – 3’ LENGTHS Black 0706-0045 Clear 0706-0042 Gray 0706-0039 5/16” ID X 1/2” OD – 3’ LENGTHS Black 0706-0046 Clear 0706-0043 Gray 0706-0040 DESCRIPTION PART # 1/8” ID – 25’ L ROLL Clear 0706-0139 3/16” ID X 5/16” OD – 25’ ROLLS Black 0706-0018 Clear 0706-0021 Gray MP12-031 DESCRIPTION PART # 1/4” ID X 7/16” OD – 25’ ROLLS Black 0706-0019 Clear 0706-0022 Gray MP12-032 5/16” ID X 1/2” OD – 25’ ROLLS Black 0706-0020 Clear 0706-0023 PREMIUM FUEL LINE •Stronger and more durable than vinyl fuel line •Use with any type of gasoline •Resists swelling and hardening •Resistant to direct sunlight, hardening and/or cracking •Flexible in temperatures from -37.2 to 73.9 °C (-35 to 165 °F) •Fuel line stretches easily over fittings or petcocks • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected models. DESCRIPTION PART # 3/16” ID 3’ Length 877261 25’ Roll 877212 1/4” ID 3’ Length 877262 25’ Roll 877213 DESCRIPTION PART # 5/16” ID 3’ Length 877263 3/8” ID 3’ Length 877264 BRAIDED FUEL LINES •Nylon-reinforced vinyl fuel line •Braided nylon within the tubing wall provides added strength •Outstanding appearance for custom fuel lines •Flexible down to 25 °F/-3.8 °C •Maximum operating temp is 65 °C (150 °F) • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected engines. DESCRIPTION PART # 1/8” ID 3’ Length 877265 25’ Roll 877207 3/16” ID 3’ Length 877266 25’ Roll 877208 1/4” ID 3’ Length 877267 25’ Roll 877209 DESCRIPTION PART # 5/16” ID 25’ Roll 877210 3/8” ID 3’ Length 877269 25’ Roll 877211 PVC VENT LINES •Constructed of soft, flexible plasticized PVC tubing •Safe to use with any type of gasoline or alcohol-type fuel •Smooth hard bore helps prevent interior buildup •Recommended for venting and overflow lines •Flexible down to -17 °C (0 °F) •Maximum dry heat temp is 104 °C (220 °F) • Sold in 3’ lengths and 25’ rolls •Made in the U.S.A. NOTE: Not for use with fuel-injected engines. DESCRIPTION PART # 1/4” ID 3’ L 0706-0204 DESCRIPTION PART # 1/4” ID (CONT) 25’ L 0706-0206 DESCRIPTION PART # 5/16” ID 3’ L 0706-0205 DESCRIPTION PART # 5/16” ID (CONT) 25’ L 0706-0207 LP (LOW PERMEATION) PREMIUM FUEL LINE •Certified to meet permeation emission standards of 15g/M2/day • On emission-controlled vehicles, check with local and state agencies to determine suitability •Robust multi-layer design and construction •Fluoropolymer liner compatible with higher ethanol-blend gasoline up to 100% • Highly flexible, easy to install and offers excellent fitting retention • Resistant to swelling, hardening and cracking caused by hydrocarbon-based fluids •Ozone and UV light resistant •Wide temperature range from -28.9 to 73.9 °C (20 to 165 °F) Gray Clear Black •Yellow color for easy identification •Use Stepless® Clamps WARNING: Not for use with fuel-injected engines. NOTE: #SNG-ENAPNR-OA-03. NOTE: Exempt per EPA CARB E.O. #Q-09-028 for offroad use.
RkJQdWJsaXNoZXIy NDI5NTY=