FORWHATEVER YOU RIDE...
JANUARY 2023 FEATURED PRODUCTS CURVE BAR END WEIGHTS • Made from aluminum • Universal-fit for most 7/ 8" and 1" handlebars • Compatible with all universal-fit Highsider bar end mirrors • Measures 1.39" in diameter x 0.66" in width • Mirror mount diameter measures 1.17" x .47" in width • Sold in pairs with mounting hardware • Weight is approximately 2.6 oz. per pair DESCRIPTION PART NO. Matte black 0634-0566 Chrome 0634-0567 DESCRIPTION PART NO. CNC Lever Guards 0618-0028 DOT BAR ENDS • Made from aluminum • Universal fit for most 7/ 8" and 1" handlebars • Compatible with all universal-fit Highsider bar end mirrors • Measures 1.39" in diameter by .66" in width • Mirror mount diameter measures 1.17" • Sold in pairs with mounting hardware DESCRIPTION PART NO. Chrome 0634-0568 Matte black 0634-0569 CHROME 0618-0028 CHROME MATTE BLACK MATTE BLACK CNC LEVER GUARDS • Provide peace of mind and additional protection for brake and clutch levers • Machined from aluminum and finished in a matte black • For use with most 7/ 8" or 1" bars • Measures approximately 71/ 4" L x 11/ 2" W • Diameter to handlebar end measures approximately 13/ 8" • Sold in pairs with mounting hardware • All Highsider and Shin Yo bar end mirrors with external clamp can be attached to the Highsider lever guards CONERO MIRROR • The most condensed version from the CONERO product line • It completes your bar end neatly with its chrome-plated aluminum build • Extremely short stem and dynamic air passage easily adjusts to your visibility needs • 3" diameter mirror head provides a clear view, and can be used on the left and right sides of the handlebar • With its minimalist and timeless design, the CONERO series fits perfectly with many motorcycles • Fitment Details: (1) Mount directly to handlebars with an outside diameter of 7/ 8" or 1", (2) Mount to existing bar ends with an O.D. of 7/ 8" or 1", (3) Compatible with all Highsider bar ends (except PART #’s 0634-0573, 0634-0583 & 0634-0584), sold separately • Diameter head: 3.14" • Overall width: 3.20" • Overall height: 4.92" • Includes 7/ 8" and 1" adapters • Tip: To block off the original handlebar mirror mounts, use Highsider M10 CNC Caps, part number 0641-0289 or 0641-0290 DESCRIPTION DIMENSIONS PART NO. Black 7.09" H x 2.36" W x 3.86" dia. 0640-1600 Black 7.09" H x 2.36" W x 3.86" dia. 0640-1617 WAVE MIRRORS DESCRIPTION PART NO. Black 0640-1628 Black/Silver 0640-1629 Black/Red 0640-1630 Black/Gold 0640-1631 Chrome 0640-1632 0640-1628 0640-1631 0640-1629 0640-1632 0640-1630 • Versatile adjustment pivot allows for maximum adjustability • Asymmetrical shape and CNC milled lines of the mirror head create an industrial look • Width head: 4.88” • Height head: 3.38” • Width: 8.85” • Height:6.88” • Stem length: 2.16” to the bend • 5.11” to the joint • 1.57” to the threaded bolt • Mounting thread M8 x 1.25 mm • Fits all Honda, Kawasaki, Suzuki, Victory and Yamaha models • Sold in pairs
JANUARY 2023 FEATURED PRODUCTS DESCRIPTION PART NO. Ponza bar end mirrors 0640-1647 DESCRIPTION PART NO. Straight bar end mirrors 0640-1649 PONZA BAR END MIRRORS STRAIGHT BAR END MIRROR • Equipped with a round plastic head and are attached to a short, straight aluminum stem • The stylish turbine design on the back of the mirror head gives the Ponza bar end mirror a further highlight • The ball head allows an individual adjustment • By a joint at the clamp, there are additional adjustment possibilities for a better view • Can be mounted on the right and left sides as well as on the top or on the bottom • E-marked • Fitment Details: (1) Mount directly to handlebars with an outside diameter of 7/ 8” or 1”, (2) Mount to existing bar ends with an O.D. of 7/ 8” or 1”, (3) Compatible with all Highsider bar ends (except PART #’s 0634-0573, 0634-0583 & 0634-0584), sold separately • Diameter, head: 3.9” • Includes 7/ 8” and 1” adapters • Fully embedded daytime running light built into the mirror stem • High-quality ABS mirror head coated in matte black • Width head 4.68” • Height head 3.54” • Total width 6.88” • Total height 6.69” • Stem length: 5.66” to the bend • Bend 1.73” to the joint • 1.57” to the threaded bolt • Mirror stem thread: M8 x 1.25 mm • Fits Honda, Kawasaki, Suzuki, Victory, Yamaha (all models) • Lightweight and durable mirror due to its plastic head • Compatible with most 7/ 8” & 1” handlebars • E-approved • Can be used in the left or right position and is available in a short or long version. • Fitment Details: (1) Mount directly to handlebars with an outside diameter of 7/ 8” or 1”, (2) Mount to existing bar ends with an OD of 7/ 8” or 1”, (3) Compatible with all Highsider bar ends (except PART No’s 0634-0573, 0634-0583, and 06340584), sold separately • 4.72” height head • 3.34” stalk length • Middle-middle: 2.95” • Includes: 1 pc. incl. reducing rings for 1” and 7/ 8” STEALTH BAR END MIRROR DESCRIPTION PART NO. X4 DRL Turn Signal Mirrors 0640-1624 X5 Short Arm Black 0640-1625 X6 Long Arm Black 0640-1626 0640-1624 0640-1625 0640-1626 UNIVERSAL BAR END MIRRORS • Round Bar End Mirror with an adjustable joint and a short, bent stem • Fits most 7/ 8” handlebars • Head diameter: 3.26” • Overall length sleeve: 1.37” • Sold in pairs NOTE: Not compatible with 1" handlebars. DESCRIPTION PART NO. Universal bar end mirrors 0640-1646 VICTORY BLAST BAR END MIRROR • Corrosion-resistant stainless steel ball clamp on the mirror head and a joint on the clamp allow adjustments for ideal viewing • Compatible with most 7/ 8" and 1" handlebars • Available in satin black DESCRIPTION PART NO. Standard Arm 0640-1609 Short Arm 0640-1610 0640-1610 0640-1609
JANUARY 2023 FEATURED PRODUCTS VICTORY EVO BAR END MIRROR • Mount directly to handlebars with an outside diameter of 7/ 8" or 1" • Mount to existing bar ends with an OD of 7/ 8" or 1" • Compatible with all Highsider bar ends DESCRIPTION PART NO. Victory EVO bar end mirror 0640-1597 DESCRIPTION PART NO. Micro LED license plate light 2030-2245 DESCRIPTION PART NO. Glow-PL1 2040-2974 DESCRIPTION PART NO. SMD LED license plate light 2030-2244 DESCRIPTION PART NO. Gloss black 0641-0289 Matte black 0641-0290 M10 CNC COVER CAPS • Covers the OEM mirror threads when converting to bar end mirrors • High-quality aluminum caps • Caps provide protection against corrosion and refine the look of the handlebars • Rubber coating is provided on the cylinder for optimum fit • For use with M10 mirror threads • Diameter: .62" • Diameter cylinder: .03" • Depth: .43" • Sold each MATTE BLACK GLOSS BLACK HIGHSIDER GLOW-PL1 • E-approved • Features a shapely, flat light module that can be easily mounted anywhere with its adhesive backer MICRO LED LICENSE PLATE LIGHT • Features three LEDs • E-marked • Measures 1.77" W x .27" H x .47" D • Sold each SMD LED LICENSE PLATE LIGHT • This self-adhesive LED license plate light features a tiny design • .25" H x .62" W x .39" D • Sold each PROTON 2 FRONT RUN AND TURN SIGNALS • One of the most compact and versatile signals in our product line • With its black housing and smoke lens, the signal can almost disappear until it is activated • A white daytime running light and a turn signal are packed into this small footprint • E-approved • For front use • Dimensions: diameter: .43", width: .47", depth: .63", thread: M8 x .71" • Universal fitment for 12V systems • Sold in pairs NOTE: The Highsider PL Control Box CB2 PART #2050-0472 switches the position light off during the flashing process and goes on again after the flashing process (with a small delay). PROTON 2 TURN SIGNALS • With smoked lenses and amber LEDs, the turn signals are only noticeable when necessary • The trend towards ever smaller lighting elements makes it possible to give the bike a cool and clean look • E-approved • For use as front or rear turn signal • Dimensions: diameter: .43", width: .47", depth: .62", thread: M8, length .70" • Universal fitment for 12V systems • Sold in pairs DESCRIPTION PART NO. Proton 2 front run and turn signals 2020-2083 DESCRIPTION PART NO. Proton 2 turn signals 2020-2082
JANUARY 2023 FEATURED PRODUCTS PROTON 3 TURN SIGNALS AND FRONT RUN AND TURN SIGNALS • Design takes ease of mounting to a new level • The small and lightweight housing is attached to wherever you need it with the help of high-strength adhesive tape • Built with black housings, smoked lenses and amber LEDs • Front run and turn signals add white daytime running lights • Once the signals are installed, they will almost disappear until they are activated • E-approved • Turn signals are for front or rear use, run and turn signals are for front use • Signal width: .43" • Measures .47" W x .47" H x .87" D • Universal fitment for 12V systems • Sold in pairs PROTON TURN SIGNALS AND RUN/TURN SIGNAL MODULES • Mounting options are only limited by your creativity • With the smoked lens and small size, the turn signal can virtually disappear • This signal is only noticeable when activated • Run/turn signal modules feature white daytime running lights • E-approved • Turn signals are for use as front or rear turn signal; run/turn signals are for front use • Dimensions: diameter: .43"; width: .5" • Universal fitment for 12V systems • Sold in pairs DESCRIPTION PART NO. Turn signals 2020-2084 Front run/turn signals 2020-20851 DESCRIPTION PART NO. Turn signals 2020-2080 Front run/turn signals 2020-20811 DESCRIPTION PART NO. Apollo bullet run/turn/brake signal 2020-2104 DESCRIPTION PART NO. Apollo run/turn/brake signal modules 2020-2103 2020-2085 2020-2084 2020-2080 2020-2081 1 The Highsider PL Control Box CB2 PART #2050-0472 switches the position light off during the flashing process and goes on again after the flashing process (with a small delay). 1 The Highsider PL Control Box CB2 PART #2050-0472 switches the position light off during the flashing process and goes on again after the flashing process (with a small delay). APOLLO BULLET RUN/TURN/BRAKE SIGNAL • Features a black aluminum housing with a smoked lens • Two ultra-bright SMD LEDs are installed in the center • Outer ring consists of the new COB technology (Chip On Board) • E-approved • For rear use • Dimensions: A: .87", B: 1.34", D: 1.57", Thread bolt M8 x .67" • Sold in pairs APOLLO RUN/TURN/BRAKE SIGNAL MODULES • Built for custom mounting in multiple locations • Includes a black aluminum ring with smoked lenses • Center of light features two ultra-bright SMD LEDs • Outer ring consists of COB LEDs (Chip On Board) • The semiconductors are bonded directly to a printed circuit board • This module comes with a black anodized aluminum ring that fits over the base body • Dimensions: A1: .51" (13mm), A2: .35" (9mm), D1: .86" (22mm), D2: .78" (20mm) • Thread Stud: M8 x 012mm • Sold in pairs Note: The unit can be installed flat without the aluminum ring, leaving only the lens visible. This requires drilling a .79" (20 mm) wide hole. Alternatively, the unit can be mounted with the aluminum ring on e.g. a retaining plate on the vehicle.
JANUARY 2023 FEATURED PRODUCTS APOLLO TURN SIGNAL MODULES AND RUN/TURN SIGNAL MODULES • Perfect for custom mounting or molding • Feature a black aluminum ring with smoked lenses and an 8mm mounting stud • Both styles feature two very bright amber SMD LEDs are installed in the center, enabling an extremely small design • The outer ring consists of the new COB technology (Chip On Board), providing the best possible efficiency and service life • Run/turn signal modules include a white daytime running light in the outer ring • COB technology allows higher light values to be achieved than with conventional LEDs • E-approved • Turn signals are for use as front or rear turn signal • Run/turn signals are for front use • Dimensions: overall depth .50", depth of center .35", overall diameter .87", diameter of center .79", thread stud: M8 x .47" • Universal fitment for 12V systems • Sold in pairs NOTE: The unit can be installed flat without the aluminum ring, leaving only the lens visible. This requires drilling a .79" hole. Alternatively, the unit can be mounted with the aluminum ring on a retaining plate. DESCRIPTION PART NO. Turn signal modules 2020-2057 2020-2057 PROTON 3 RUN/TURN/BRAKE SIGNALS • Design takes ease of mounting to a new level • The small and lightweight housing is attached to wherever you need it with the help of high-strength adhesive tape • Built with black housings, smoked lens, and super bright LEDs • Once the signals are installed, they will almost disappear until they are activated • E-approved • For rear use • Dimensions: width: .43"; width: .47"; height: .47"; depth: .87" • Sold in pairs PROTON 2 RUN/TURN/BRAKE SIGNALS • Packed with run, turn, and brake functions • Smoked lenses • Mounting is made easy with the built-in 8mm mounting stud • With a Highsider Proton turn signal, the lighting on the motorcycle can virtually disappear visually • This indicator is only noticeable when it really has to be • Dimensions: diameter: .43"; width: .47"; depth: .63" • Sold in pairs PROTON RUN/TURN/BRAKE SIGNAL MODULES • Truly one of the most unique signals on the market • These signals can be installed in a multitude of ways for your custom needs • E-approved • For rear use • Dimensions: diameter: .43 "; width (depth): .51" • Sold in pairs PROTON RUN/BRAKE SIGNAL • One of the most unique signals on the market • These signals can be installed in a multitude of ways for your custom needs • Once installed, the turn signal can virtually disappear optically • This light is only noticeable when necessary • The trend towards ever smaller lighting elements makes it possible to give the bike a cool and clean look • E-approved • For rear use • Measures .43" dia. x .5" W • Weighs: .009 lb. • Sold each PROTON 3 RUN/BRAKE SIGNALS • Designed to virtually disappear visually due to its small size and smoke lens, this taillight only stands out when it really has to • The trend towards ever smaller lighting elements makes it possible to give the bike a cool and clean look • The Proton 3 family is attached to any flat surface by very strong, double-sided adhesive tape • E-approved • For rear use • Measures .47" H x .47" W x .87" D • Sold each DESCRIPTION PART NO. Proton run/brake signal 2010-1481 DESCRIPTION PART NO. Proton 2 run/turn/brake signals 2020-2116 DESCRIPTION PART NO. Proton 3 run/turn/brake signals 2020-2117 DESCRIPTION PART NO. Proton 3 run/brake signals 2010-1482 DESCRIPTION PART NO. Proton run/turn/brake signal modules 2020-2115
JANUARY 2023 FEATURED PRODUCTS DESCRIPTION PART NO. Highsider FT13 LED headlight 2001-2576 HIGHSIDER FT13 LED HEADLIGHT • Combines a compact design and high light output • Headlamp's matte black housing is made from high-quality aluminum and is equipped with a robust steel bracket • LED provides a symmetrical, bright light for optimum perception • Dimensions: diameter: 2.16", diameter lens: 1.73", distance of the mounting holes: 2.12", mounting holes on the side: M4 • Includes mounting and E-box for voltage control TYPE 8 ADAPTIVE 7" LED HEADLIGHT ASSEMBLIES DESCRIPTION PART NO. Black 2001-2571 Chrome 2001-2572 TYPE 8 ADAPTIVE 7" LED HEADLIGHT ASSEMBLIES WITH R1 FRAME • Features a unique built-in halo running light • R1 aluminum frame is offered as a bottom mount or side mount • Tilt-activated adaptive cornering lights offer visible advantages over a conventional headlight • The cornering light activates when the motorcycle is leaned over in corners to better improve road illumination • Two ellipsoidal lenses in combination with powerful LEDs turn night into day • Black finish • E-approved and DOT-compliant • Sold each DESCRIPTION PART NO. Side mount 2001-2573 Bottom mount 2001-2574 TYPE 8 ADAPTIVE 7" LED HEADLIGHT INSERTS • The perfect way to improve visibility at all times • The cornering light activates when the motorcycle is leaned over in corners to better improve road illumination • Compatible with most 7" headlight housings • DOT-compliant • Sold each DESCRIPTION PART NO. Chrome reflector 2001-2577 Black reflector 2001-2578 2001-2572 2001-2571 2001-2574 2001-2573 2001-2578 2001-2577 • Features a unique built-in halo running light • The headlight is pre-installed into a classic headlight bucket and includes a secure mounting bracket for easy mounting • Thanks to advances made with modern LED lighting technology, forward visibility will no longer be an issue • Tilt-activated adaptive cornering lights offer clear advantages over a conventional headlight • The cornering light activates when the motorcycle is leaned over in corners to better improve road illumination • Two ellipsoidal lenses in combination with powerful LEDs turn night into day • E-approved and DOT compliant • Sold each
JANUARY 2023 FEATURED PRODUCTS 5-3/4" TYPE 7 LED HEADLIGHT • Includes a built-in LED Halo ring • The low beam lights up in the upper half of the insert and when the high beam is switched on, both halves light up • Compatible with most 53/ 4" headlight housings • E-approved and DOT-compliant • Cable length: 15¾” • Sold each 5-3/4" LED TYPE 6 HEADLIGHT • Built with the latest LED technology • Includes a chrome-plated reflector, built-in LED Halo ring and daytime running light • The daytime running light is in the middle of the strip; low beam is in the upper half of the insert • Both halves light up when high beam is switched on • E-approved and DOT compliant • Cable length: 153/ 4" • One-piece 6" ULTIMATE LED HEADLIGHT ASSEMBLY WITH WAVE MOUNT • The Highsider Ultimate LED Headlight is the perfect solution to give your bike a facelift • The Ultimate Headlight pairs a stacked rectangular low beam and high beam unit with our CNC aluminum Wave headlight mount • Mounting is also made easy with built-in side mounting holes that are compatible with any of our headlight mounts, sold separately • The low beam also has an integrated position light • Sold each EXTEND CNC HEADLIGHT MOUNTING BRACKETS • Mounts are adjustable from 1.37" to 3.54" allowing the user to adjust the headlight for optimum looks and headlight performance • Constructed from aluminum and finished with a black anodized coating, making the Extend brackets incredibly lightweight and durable • Perfect for custom installs on choppers, cruisers or naked bikes • Attach to the fork with our proprietary headlight clamps, sold separately or as a set with clamps • Dimensions: thickness: .47", length holder min: 1.37" (measured center hole to headlight mount), length holder max: 3.74" (measured center hole to headlight mount), height: 2.16", hole diameter: 10mm • Clamps sold in pairs; brackets with clamps include four clamps DESCRIPTION PART NO. Brackets 2001-2559 Brackets w/ clamps for 38-41mm forks 2001-2560 Brackets w/ clamps for 42-43mm forks 2001-2561 2001-2561 2001-2559 DESCRIPTION PART NO. 53/4” Type 7 LED headlight 2001-2580 DESCRIPTION PART NO. 5-3/4” LED type 6 headlight 2001-2581 DESCRIPTION PART NO. 6” Ultimate LED headlight assembly with wave mount 2001-2570
RkJQdWJsaXNoZXIy NDI5NTY=